Common mode impedance
The resistance the choke presents to common mode noise, quoted at a stated frequency. Compare candidates at the same frequency or the values do not correspond.
インダクター製品
WHPL1211A Common Mode Chokes
WHPL1211A shares a size band with WHAL1211A but carries its own specification. Similar naming is not a licence to treat them as equivalents, so read both datasheets and compare impedance at the frequency your measurement actually fails.
型番検索・選定
WHPL1211A Common Mode Chokesの型番を検索
この表では、海外サイトの現行製品データ、公開済みの選定項目、型番別の技術資料リンクを使用しています。
※画像列と型番列は固定されています。横にドラッグしてすべての仕様を確認できます
| 画像 | データシート | 比較 | ダウンロード |
最大寸法（L×W×H）
|
Z（Ω）100MHz/0.1V 最小値
|
Z（Ω）100MHz/0.1V 参考値
|
最大DC抵抗（mΩ）
|
最大定格DC電流（A）
|
最小絶縁抵抗（MΩ）
|
最大定格電圧（V）
|
サンプル |
|---|
| 画像 | 型番 | データシート | 比較 | ダウンロード | 最大寸法（L×W×H） | Z（Ω）100MHz/0.1V 最小値 | Z（Ω）100MHz/0.1V 参考値 | 最大DC抵抗（mΩ） | 最大定格DC電流（A） | 最小絶縁抵抗（MΩ） | 最大定格電圧（V） | サンプル |
|---|---|---|---|---|---|---|---|---|---|---|---|---|
 |
WHPL-1211A-231T0 | SPEC | 1211 | 80 | 230 | 4 | 10 | 10 | 125 |
|
||
 |
WHACM12A65R272 | SPEC | 1211 | 2300 | 2700 | 50 | 1.5 | 10 | 125 |
|
||
|
|
WHACM12A65R222 | SPEC | 1211 | 2200 | 2500 | 35 | 1.8 | 10 | 125 |
|
||
|
|
WHACM12A65R102 | SPEC | 1211 | 750 | 1000 | 14 | 6 | 10 | 125 |
|
||
|
|
WHACM12A65R801 | SPEC | 1211 | 600 | 800 | 8 | 8 | 10 | 125 |
|
||
|
|
WHACM12A65R701 | SPEC | 1211 | 500 | 700 | 6 | 8 | 10 | 125 |
|
||
|
|
WHACM12A65R800 | SPEC | 1211 | 80 | 230 | 2 | 10 | 10 | 125 |
|
一致する型番がありません
選択した条件を広げるか、現在の検索条件をクリアしてください。
By series
Power line common mode choke families
Families differ in construction and size band, which sets impedance and current together.
選定方法
Selecting a power line common mode choke in four steps
Work from the failing frequency band outward to current, losses and board space.
- 01
Identify the failing band
Read the frequency range where your conducted emission scan exceeds the limit. That band, not a general noise complaint, decides which impedance curve you need.
- 02
Match the impedance curve
Pick a part whose common mode impedance peaks across the failing band. Read the impedance at that frequency, not the headline figure at the family's peak.
- 03
Check current and DC resistance
The rated current must cover the worst-case load with margin. DC resistance sets the voltage drop and the heat the winding has to shed.
- 04
Confirm the mechanical fit
Check size, land pattern and clearance to neighbouring parts, then re-scan on your own board because layout changes the result.
Parameters
Reading common mode choke ratings
Impedance is a curve, not a single number, so read the test frequency with the value.
定格電流
The continuous current the winding carries under stated temperature-rise conditions. Derate for ambient temperature and restricted airflow inside the enclosure.
DC resistance
Winding resistance, usually a maximum figure. It sets the conduction loss and the voltage drop the supply has to tolerate at full load.
Common mode inductance
Measured with both windings in the common mode configuration. Higher inductance generally moves the impedance peak toward lower frequencies.
Leakage inductance
The part of the winding that does not couple. It acts on differential signals and can be useful, but it also limits how high a current the part handles.
Withstand voltage
Isolation between the two windings under a stated test. Select against the safety requirement that applies to the equipment, not the working voltage.
比較
Common mode choke families side by side
Size band drives impedance and current capability more than family naming does.
選定表に戻る ↑| 最大寸法（L×W×H） | 型番数 | Z（Ω）100MHz/0.1V 最小値 | Z（Ω）100MHz/0.1V 参考値 | 最大DC抵抗（mΩ） | 最大定格DC電流（A） | 最小絶縁抵抗（MΩ） | 最大定格電圧（V） | 操作 |
|---|---|---|---|---|---|---|---|---|
| 1211 | 7 | 80, 500, 600, 750, 2200, 2300 | 230, 700, 800, 1000, 2500, 2700 | 2, 4, 6, 8, 14, 35, 50 | 1.5, 1.8, 6, 8, 10 | 10 | 125 | 絞り込み → |
| 1513 | 5 | 225, 400, 500, 800, 1200 | 300, 500, 700, 1000, 1500 | 5, 6, 7, 10, 23 | 5, 9, 10, 13 | 10 | 80 | 絞り込み → |
| 4520 | 14 | 60, 90, 180, 200, 250, 300, 350, 500, 650, 800, 1000, 1200, 1800, 2500 | 90, 150, 230, 300, 380, 420, 500, 700, 900, 1000, 1200, 1400, 2000, 3000 | 35, 40, 45, 50, 55, 58, 60, 70, 80 | 1, 1.5, 1.9, 2.0, 2.1, 2.2, 2.4, 2.5, 3, 3.2 | 10 | 50 | 絞り込み → |
| 7060 | 9 | 40, 100, 225, 275, 500, 800, 910, 2000, 2500 | 70, 140, 300, 450, 700, 1020, 1300, 2700, 3000 | 5, 10, 15, 17, 21, 63, 75 | 0.9, 1, 2.5, 3, 4, 5, 9, 15 | 10 | 125 | 絞り込み → |
| 9070 | 6 | 225, 450, 500, 750, 1700, 2500 | 300, 600, 700, 1000, 2200, 3000 | 6, 8, 10, 13, 60, 75 | 2.5, 3, 4, 5, 5.5, 6 | 10 | 50 | 絞り込み → |
用途別確認
Where power line common mode chokes are fitted
Confirm the line current, the failing band and how much board space the filter can take.
AC mains input filtering
- Confirm the line current and the failing band from the conducted scan, then verify the withstand voltage meets the equipment safety case.
DC power distribution
- Check the rated current against the worst-case load and confirm DC resistance does not push the rail below tolerance at full draw.
Motor drives and inverters
- Switching noise is broadband. Verify the impedance curve covers the whole failing range, not just the fundamental switching frequency.
Industrial power supplies
- Space and temperature rise usually decide. Confirm the derated current at the real ambient inside the enclosure.
Documents
Common mode choke datasheets and drawings
Datasheets carry the impedance curve, current rating and recommended land pattern.
代表的な入手可能資料を表示しています。特定のSKUは検索して確認してください。
- 7
- PDFデータシート掲載数
- 1
- 3Dファイル掲載数
- 0
- PCBフットプリント掲載数
VOOHUが公開する製品情報は、エンジニアリングチームが確認しています。仕様、ダウンロード資料、技術サポート情報は型番ごとに紐付けられているため、サンプルや見積もりを依頼する前に確認できます。
カテゴリー概要
How a common mode choke works and how to choose one
Most selection mistakes here come from treating impedance as a single number, or from confusing common mode with differential mode noise.
型番が決まっている場合は、サンプルまたは見積もりを依頼。
Common mode versus differential mode
Differential noise travels out on one conductor and back on the other. Common mode noise travels the same direction on both and returns through ground. A choke winds both conductors on one core so their supply currents cancel, while common mode current sees a high impedance. That is why it filters one and passes the other.
Impedance is a curve
The headline impedance figure is measured at one frequency. What matters is whether the curve is high across the band where your conducted emission scan actually fails. A part with a higher peak in the wrong place will not help. Read the curve from the datasheet, identify your failing band first, and match the two.
What limits the choice
Rated current and DC resistance set the ceiling. A choke with excellent impedance is useless if the winding cannot carry the load current, or if its resistance drops the rail below tolerance. Check those against worst case, then confirm on your own board, because layout and the rest of the filter change the measured result.
よくあるご質問
Common mode choke questions engineers ask
Answers cover how the choke works, how to read impedance and where it belongs.
How does WHPL1211A differ from WHAL1211A?
The two share a size band, but impedance, rated current and DC resistance are each defined by their own datasheet. Naming similarity reflects a size convention rather than electrical equivalence. Compare the two datasheets item by item before treating either as a substitute for the other.
Can I use the WHAL land pattern for WHPL?
Verify it from the datasheet rather than assuming. Parts in the same size band often share a footprint, but pin arrangement, body tolerance and recommended pad geometry are stated per part. A mismatch that looks minor on the drawing can cause placement and reflow problems in production.
Which one should I evaluate first?
Start from your requirement, not from the part number. Identify the frequency band that fails, the line current and the board space, then read both datasheets against those three constraints. Whichever covers them with more margin is the one to sample first.
Does the same rated current apply to both?
No, each part states its own. Rated current depends on winding design and the temperature rise the part was qualified to, which can differ between two parts of the same physical size. Read the figure from the specific datasheet and derate for your actual ambient conditions.
How do I request samples or a quote?
With a complete part number, send the part number, quantity, delivery region and the date you need it. If you are still selecting, send the line current, the frequency band where your scan fails and the board space available, and a sales engineer will confirm candidates first.
エンジニアサポート
製品選定後のご相談
候補型番と、確認が必要な条件をお送りください。候補が明確になった後にサンプル支援を追加でき、商取引に関するご質問も同じ技術相談の中でご相談いただけます。
- 1選択した型番
- 2エンジニア確認
- 3サンプル申請
- 4商談
代替品評価をご希望の場合
- 元の型番とデータシート
資料のリビジョンも記載してください
- 動作条件
温度、絶縁電圧、PoE電流の条件
- パッケージ制約
ピン数、ピッチ、ピン列間隔
- プロジェクト段階と年間数量
サンプルと評価の優先度確認に使用します
- 希望確認日
候補と相違点の比較が必要な時期
エンジニア確認により候補型番を選び、相違点をご説明します。
サンプル・見積もりをご希望の場合
- 候補型番
選定表またはエンジニア確認で選んだ型番
- 数量とプロジェクト段階
試作／パイロット生産／量産
- 希望納期
サンプルと量産の時期を分けて記載してください
- 必要資料
適合資料、材料宣言、第三者機関レポートなど
サンプル数量、リードタイム、費用は、プロジェクト段階と型番によって異なります。営業担当者より営業日にご回答します。
