Package size and dimensions
Stated as length by width by height in millimetres. Height is often the binding constraint, and within one footprint the taller option usually carries more current.
インダクター製品
Molded Power Inductors
Molded construction encloses the winding in a magnetic compound, giving a self-shielded part with low audible noise and a soft saturation curve. The range runs from 4.4 by 4.2 millimetres up to 23.5 by 22, covering 0.1 to 150 microhenries and RMS currents to 70 amps.
型番検索・選定
Molded Power Inductorsの型番を検索
この表では、海外サイトの現行製品データ、公開済みの選定項目、型番別の技術資料リンクを使用しています。
※画像列と型番列は固定されています。横にドラッグしてすべての仕様を確認できます
| 画像 | データシート | 比較 | ダウンロード |
パッケージサイズ
|
寸法（L×W×H）
|
インダクタンス値
|
DCR（mΩ）
|
IRMS
|
ISAT
|
サンプル |
|---|
| 画像 | 型番 | データシート | 比較 | ダウンロード | パッケージサイズ | 寸法（L×W×H） | インダクタンス値 | DCR（mΩ） | IRMS | ISAT | サンプル |
|---|---|---|---|---|---|---|---|---|---|---|---|
 |
WHYTP0320 series | SPEC | WHYTPシリーズ | 3.4×3.2×1.8mm | 0.33～10uH | 21-422mΩ | 1.4-8A | 1.6-10A |
|
一致する型番がありません
選択した条件を広げるか、現在の検索条件をクリアしてください。
By series
Molded inductor series by size band
Series split by footprint and height, which together set current capability and loss.
選定方法
Selecting a molded power inductor in four steps
Ripple sets the inductance; IRMS and ISAT set the size; height often decides.
- 01
Calculate the inductance
Derive it from input and output voltage, switching frequency and the ripple current you can accept. Then check the tolerance band at its worst corner.
- 02
Check both current ratings
IRMS caps the continuous current by temperature rise. ISAT caps the peak by inductance roll-off. Your design has to satisfy both, not the friendlier one.
- 03
Pick the size band
Larger footprints and taller bodies give lower DC resistance and higher current. Work back from the height clearance over the converter.
- 04
Verify on the board
Measure ripple, efficiency and the inductor's temperature at full load in the real enclosure, then confirm at the highest rated ambient.
Parameters
Reading molded inductor ratings
IRMS and ISAT are defined differently and both have to be satisfied.
Inductance value
Ranges from about 0.1 to 150 microhenries across the family. Low values suit high switching frequency; higher values reduce ripple at lower frequency.
DC resistance
From about 0.65 milliohm on the largest low-value parts up to several hundred milliohms on the small high-inductance ones. It sets conduction loss.
IRMS
The continuous RMS current producing the datasheet's stated temperature rise. It is the steady-state limit and must be derated for high ambient temperature.
ISAT
The current at which inductance falls by the stated percentage. It caps the instantaneous peak, including startup inrush and load transients.
シールド
Molded construction encloses the winding in magnetic material, so the part is inherently shielded. That reduces coupling into nearby traces and lowers audible noise.
比較
Molded inductor series side by side
Footprint and height together decide what current and inductance are available.
選定表に戻る ↑| パッケージサイズ | 型番数 | 寸法（L×W×H） | インダクタンス値 | DCR（mΩ） | IRMS | ISAT | 操作 |
|---|---|---|---|---|---|---|---|
| WHYTシリーズ | 11 | 7.0×6.6×2.8mm, 7.0×6.6×3.8mm, 7.0×6.6×4.8mm, 11.5×10×2.8mm, 11.5×10×3.8mm, 11.5×10×4.8mm, 13.45×12.6×4.8mm, 13.45×12.6×5.8mm, 13.45×12.6×6.5mm, 17.15×17.15×7mm, 23.5×22×12.6mm | 0.22～47uH, 0.68～47uH, 0.47～47uH, 0.22～33uH, 0.15～100uH, 0.22～100uH, 4.7～150uH, 4.7～100uH, 2.2～100uH, 1.00～100.00uH | 3-385mΩ, 4.8-320mΩ, 3.9-230mΩ, 0.89-160mΩ, 0.65-340mΩ, 0.8-290mΩ, 0.7-130mΩ, 9-350mΩ, 8.5-170mΩ, 2.5-130mΩ, 0.95-40mΩ | 1.5-24A, 1.8-17A, 2-20A, 4-50A, 2-45A, 2.1-37A, 3-50A, 1.5-15A, 3.5-16A, 3.7-29A, 11-70A | 2-34A, 2.5-19A, 2.6-21A, 2.6-33A, 2.3-75A, 2.8-65A, 5-75A, 2.7-24A, 4-24A, 5-34A, 9-60A | 絞り込み → |
| WHYTAシリーズ | 7 | 4.4×4.2×1.0mm, 4.4×4.2×1.8mm, 5.4×5.2×1.6mm, 5.4×5.2×2.8mm, 7.0×6.6×1.3mm, 7.0×6.6×1.6mm, 7.0×6.6×2.2mm | 0.15～4.7uH, 0.1～10uH, 0.47～10uH, 0.1～22uH, 0.22～22uH | 9-195mΩ, 4-282mΩ, 9-155mΩ, 3-125mΩ, 8.5-175mΩ, 2.3-350mΩ, 3-230mΩ | 1.8-7.5A, 1.6-13A, 2.5-10.5A, 3.2-25A, 2-10A, 1.8-25A, 2-21A | 2.2-15A, 2-22A, 3-15.5A, 3.5-30A, 3-16A, 2.3-38A, 2.5-34A | 絞り込み → |
| WHYTPシリーズ | 1 | 3.4×3.2×1.8mm | 0.33～10uH | 21-422mΩ | 1.4-8A | 1.6-10A | 絞り込み → |
用途別確認
Where molded power inductors are used
Confirm output current, switching frequency, ripple budget and height clearance.
DC-DC converters and POL rails
- Confirm the ripple budget and switching frequency, then check IRMS at the real ambient and ISAT against startup inrush.
Automotive and industrial supplies
- Ambient temperature and vibration both matter. Derate IRMS for the environment and confirm the mounting suits the vibration profile.
Compact consumer boards
- Height usually decides. Work back from the clearance available, then confirm the chosen size band still meets both current ratings.
Noise-sensitive equipment
- Molded parts are inherently shielded and quieter than open wirewound. Verify audible noise at your switching frequency on the real assembly.
Documents
Molded inductor datasheets and drawings
Datasheets carry the saturation curve, temperature rise data and land pattern.
代表的な入手可能資料を表示しています。特定のSKUは検索して確認してください。
WHYT2313 seriesWHYTシリーズ
WHYTP0320 seriesWHYTPシリーズ
WHYT1770 seriesWHYTシリーズ
WHYT1265 seriesWHYTシリーズ
WHYT1260 seriesWHYTシリーズ
WHYT1250 seriesWHYTシリーズ
- 19
- PDFデータシート掲載数
- 0
- 3Dファイル掲載数
- 0
- PCBフットプリント掲載数
VOOHUが公開する製品情報は、エンジニアリングチームが確認しています。仕様、ダウンロード資料、技術サポート情報は型番ごとに紐付けられているため、サンプルや見積もりを依頼する前に確認できます。
カテゴリー概要
Molded versus wirewound, and which current rating binds
Two questions decide most molded inductor selections: whether the construction is right for the design, and which of the two current figures limits you.
型番が決まっている場合は、サンプルまたは見積もりを依頼。
What molded construction changes
The winding is encased in a magnetic composite rather than wound on an exposed core. That makes the part self-shielding, so it couples less into neighbouring traces, and it damps the movement that causes audible buzz. It also gives a softer saturation curve, where inductance falls gradually rather than collapsing.
IRMS and ISAT do different jobs
IRMS is a thermal limit: the continuous RMS current that produces the stated temperature rise. ISAT is a magnetic limit: the current at which inductance has dropped by a stated percentage. A design has to satisfy both. Steady-state load is checked against IRMS, and peaks including startup inrush against ISAT.
Height is usually the real constraint
Within the same footprint, a taller body has more winding volume, which means lower DC resistance and higher current for the same inductance. The range spans from one millimetre high up to more than twelve. In practice the clearance over the converter often decides the series before any electrical parameter does.
よくあるご質問
Molded power inductor questions engineers ask
Answers cover molded versus wirewound, IRMS against ISAT, and shielding.
What is a molded power inductor?
It is an inductor whose winding is encased in a magnetic composite material rather than wound on an exposed core. The construction makes the part self-shielding, reduces audible noise and gives a softer saturation characteristic. They are widely used in DC-DC converters where board space and magnetic coupling both matter.
How does molded compare with wirewound construction?
Molded parts are self-shielded, so they couple less noise into nearby traces, and they are quieter because the winding cannot move. Their saturation curve is softer, falling gradually rather than collapsing. Open wirewound parts can offer lower cost at some sizes. Compare on DCR, IRMS, ISAT and the shielding your layout needs.
What is the difference between IRMS and ISAT?
IRMS is a thermal rating: the continuous RMS current that produces the temperature rise stated in the datasheet. ISAT is a magnetic rating: the current at which inductance has fallen by a stated percentage. Both must be satisfied, IRMS for steady-state load and ISAT for peaks including startup inrush.
Which one usually limits the design?
It depends on the load profile. A steady high current load is usually limited by IRMS and temperature rise. A load with large fast transients, or a converter with significant startup inrush, is usually limited by ISAT. Check both against your actual current waveform rather than assuming.
How do I choose between size bands?
Start from the height clearance over the converter, because that is often the binding mechanical constraint. Within a footprint, a taller body gives lower DC resistance and higher current for the same inductance. Then confirm the band you can fit still meets both current ratings with margin.
Does molded construction really reduce noise?
It reduces two things. Magnetically, the enclosed winding radiates less into neighbouring traces, which helps in dense layouts. Acoustically, the encapsulation damps the winding movement that causes audible buzz at switching frequencies in the audio band. Verify both on your own assembly.
How much should I derate for temperature?
IRMS is defined for a stated temperature rise from a stated ambient. If your enclosure runs hotter or has restricted airflow, the usable current is lower. Measure the part's temperature at full load in the real enclosure at the highest rated ambient rather than trusting the headline figure.
How do I request molded inductor samples or a quote?
With a complete part number, send the part number, quantity, delivery region and the date you need it. If you are still selecting, send the output current, switching frequency, ripple budget, height clearance and ambient temperature, and a sales engineer will shortlist candidates.
エンジニアサポート
製品選定後のご相談
候補型番と、確認が必要な条件をお送りください。候補が明確になった後にサンプル支援を追加でき、商取引に関するご質問も同じ技術相談の中でご相談いただけます。
- 1選択した型番
- 2エンジニア確認
- 3サンプル申請
- 4商談
代替品評価をご希望の場合
- 元の型番とデータシート
資料のリビジョンも記載してください
- 動作条件
温度、絶縁電圧、PoE電流の条件
- パッケージ制約
ピン数、ピッチ、ピン列間隔
- プロジェクト段階と年間数量
サンプルと評価の優先度確認に使用します
- 希望確認日
候補と相違点の比較が必要な時期
エンジニア確認により候補型番を選び、相違点をご説明します。
サンプル・見積もりをご希望の場合
- 候補型番
選定表またはエンジニア確認で選んだ型番
- 数量とプロジェクト段階
試作／パイロット生産／量産
- 希望納期
サンプルと量産の時期を分けて記載してください
- 必要資料
適合資料、材料宣言、第三者機関レポートなど
サンプル数量、リードタイム、費用は、プロジェクト段階と型番によって異なります。営業担当者より営業日にご回答します。
