Skip to main content
VOOHU RJ45 Inline Couplers products

I/O Connector products

RJ45 Inline Couplers

Join RJ45 cable interfaces or select a feedthrough for an equipment panel. Compare RJ45 inline couplers by Cat5e/Cat6 category, shielding and mounting design, then review wiring, dimensions and channel requirements. Request samples or volume pricing for your selected part.

Part number search & selector

Find RJ45 Inline Couplers part numbers

The table uses the current English-site product records, published selection fields and part-specific technical-file links.

* Frozen Image and Part Number columns · drag horizontally to review all specifications

RJ45 Inline Couplers product selection results
Image Part number Datasheet Compare Downloads Network LevelTransmission BandwidthShieldGold plating of contactsPanel Sample
VOOHU SYTZT1188IWA17DY3S2T5E387A RJ45 Inline Couplers SYTZT1188IWA17DY3S2T5E387A SPEC Cat5e100MHzNO3UYES
VOOHU SYTZT1188GWC8D3T5E387 RJ45 Inline Couplers SYTZT1188GWC8D3T5E387 SPEC Cat5e100MHzYES6UNO

Product family quick links

Start with Network Level

Counts by network level come from the current records, from Cat3 voice-grade parts up to 250 MHz Cat6 couplers.

How to select

Picking an RJ45 inline coupler for the channel

An RJ45 inline coupler has one job: join two runs without becoming the weakest element of the channel. Check wiring, category, shield and mounting, in that order.

  1. 01

    Confirm straight-through or special wiring

    Check both interfaces, gender and contact mapping. A one-to-two adapter is a different part from an ordinary RJ45 coupler and needs its own review.

  2. 02

    Match the cabling category

    Use a Cat5e coupler on a Cat5e channel and a Cat6 coupler at or above the installed cable grade; a blank category field is not a pass.

  3. 03

    Choose shielding and mounting

    On screened cable use a shielded coupler so the screen stays continuous, then review panel retention, cutout and cable clearance.

  4. 04

    Validate the channel and request supply

    Test at the intended length, data rate and power, then send the part number, quantity and timing for a quote.

Key selection parameters

RJ45 coupler specifications: category, shield and plating

The selector lists five fields for each RJ45 coupler. They describe the component; the channel result also depends on cables, plugs and termination quality.

01

Network level

Cat3, Cat5e or Cat6 as published for the part. Confirm the level in the datasheet rather than reading it from the part number.

02

Transmission bandwidth

16, 100 or 250 MHz, in line with Cat3, Cat5e and Cat6. MHz describes the frequency range, not the data rate in Mb/s.

03

Shield

YES parts carry the cable screen through the join; NO parts are unshielded. Continuity still depends on the cables and the equipment grounding.

04

Contact gold plating

3U, 6U or 50U, meaning microinches of gold on the contact area. Thicker plating suits ports that are re-mated often.

05

Panel

YES parts have panel mounting features. A panel mount coupler needs its clip or fastener, cutout, panel thickness and access to both latches checked.

Product family comparison

Cat3, Cat5e and Cat6 RJ45 couplers compared

Rows group the range by network level. Cat6 parts make up most of the listing, while Cat3 and Cat5e parts suit voice and 100 MHz channels. Confirm the shield, plating and panel fields in each part row.

Return to the selector ↑
Network LevelPartsTransmission BandwidthShieldGold plating of contactsPanelAction
Cat3116MHzYES6UNOFilter →
Cat5e2100MHzYES, NO3U, 6UYES, NOFilter →
Cat612250MHzYES, NO3U, 6U, 50U, -YES, NOFilter →
-4-YES6U, 50U, -NOFilter →

Technical performance & application fit

Where an inline coupler sits in a real installation

A network coupler is a connection point, so it is reviewed as part of the channel. Send the cable grade, the run lengths on either side and the panel details.

Application review

Equipment panel feedthroughs

  • Use a panel mount RJ45 coupler where an internal cable meets an external one
  • Check panel retention and mating clearance on both sides
  • Keep the shield path continuous to chassis on screened systems
Application review

Patch cable extension and repair

  • Join two existing patch leads with an Ethernet cable coupler instead of re-terminating
  • Keep the total channel within its length limit
  • Re-test the channel after adding the join
Application review

Wall plates and patch panels

  • Check whether the opening needs a keystone coupler
  • Confirm the retention format from the part drawing
  • Match the coupler category to the installed cabling
Get technical support →

Downloads & technical resources

RJ45 coupler datasheet and 3D model search

Search a full or partial part number to open its datasheet or 3D model. Use the drawing for wiring, panel cutout and plating, since couplers that look alike can differ in all three.

19
PDF datasheets listed
14
3D file sets listed
0
PCB footprints listed

VOOHU’s published product content is reviewed by its engineering team. Specifications, downloads and technical support information are tied to specific part numbers, so you can verify them before requesting samples or a quotation.

Category overview

What an RJ45 inline coupler does to the link

Couplers are simple parts, but two questions come up constantly: whether they slow the link, and which category to use.

01

It joins two runs without re-terminating

An RJ45 coupler mates two RJ45 plugs back to back, so two existing cable runs become one channel without cutting and re-terminating either end. That is its whole purpose: extending or repairing a run with existing patch leads rather than making up a new cable.

The basic form is an RJ45 female to female coupler with straight-through wiring, sometimes called an RJ45 joiner. It is passive. It is not a switch, a repeater or an RJ45 extender with gain, so the joined channel still has to stay within the 100 m BASE-T limit.

02

Does it slow the connection

Not in the sense people usually mean. An Ethernet coupler does not reduce the negotiated link speed. It adds a connection point, which introduces an impedance discontinuity and a small insertion loss. On a short gigabit run that sits inside the margin. Near the length limit, or at 10G, it consumes margin already thin.

The component limits behind that margin are NEXT, return loss and insertion loss, which TIA-568 sets for Cat5e hardware to 100 MHz and Cat6 hardware to 250 MHz. A coupler that is not tested to those limits can pass on a short channel and fail on a longer one.

03

Match the category to the channel

The channel performs to its weakest element, so a Cat5e coupler caps a Cat6A channel at Cat5e. Use a coupler at or above the category of the cable and the link. On screened installations, use a shielded RJ45 coupler so the screen stays continuous through the join, or the shielding is defeated at that point.

The published levels stop at Cat6 (250 MHz). A few part numbers include CAT6a in the name, but the listed level is Cat6; for a channel that needs a Cat6A inline coupler rated to 500 MHz, check the datasheet or ask FAE before design-in. No Cat7 coupler is listed.

FAQ & related guides

RJ45 coupler questions on speed, PoE and shielding

Answers on speed, category, PoE, shielding and wiring. The values for each RJ45 coupler part number come from its own datasheet.

Does an RJ45 coupler reduce Ethernet speed?

It does not change the negotiated speed, but it adds a connection and some channel loss. The result depends on the coupler, cables, length, termination quality and target rate. Choose a part documented for the channel category and test the complete link instead of assuming zero loss.

How do I choose between a Cat5e coupler and a Cat6 inline coupler?

Match the cabling system, not the advertised data rate of the device. Cables, plugs and coupler must all meet the channel category, and fitting one Cat6 part does not upgrade a Cat5e channel. Published levels on this page are Cat3, Cat5e and Cat6.

Do you list a Cat6A coupler?

Not as a published level. Some part numbers carry CAT6a in their names, but the selector lists them as Cat6 at 250 MHz. If your channel is Cat6A, send the requirement and ask FAE to confirm test data to 500 MHz before choosing a part.

What is the difference between shielded and unshielded RJ45 couplers?

A shielded design carries the cable screen across the join and needs a grounded path through the cables and equipment. An unshielded design does not provide that continuity. A metal-looking body alone does not establish EMC performance.

Can an RJ45 coupler be used for PoE?

Assess the specific part and system: power level, contact resistance, temperature rise and mating conditions. A Cat6 or 8P8C label does not establish PoE, PoE+ or PoE++ suitability.

Do all female-to-female couplers use the same wiring?

Do not assume so. Straight-through couplers map pin 1 to pin 1, while special adapters and one-to-two splitters use different contact maps. Check the wiring diagram and viewing orientation in the part drawing.

Can a passive one-to-two RJ45 adapter replace a switch?

No. A passive adapter does not switch Ethernet traffic. Any permitted wiring arrangement depends on its internal connections and the equipment at both ends; it does not create two independent switched ports.

How do I request RJ45 coupler samples and bulk pricing?

Send the part number, sample or production quantity, shielding and mounting needs, destination and timing. If no part is chosen yet, start with the cabling category and the installation constraints.

Engineer support

Continue after product selection

Send the candidate part number and the condition you need reviewed. Sample support can be added after the selection is clear; commercial questions may be discussed in the same engineering conversation.

  1. 1Selected part numbers
  2. 2Engineering review
  3. 3Sample request
  4. 4Commercial discussion

For a replacement review

  • Original part and datasheet

    Include the document revision

  • Operating conditions

    Temperature, isolation voltage and PoE current basis

  • Package constraints

    Pin count, pitch and spacing between pin rows

  • Project stage and annual volume

    To help prioritize samples and evaluation

  • Target review date

    When you need candidates and a comparison of differences

Engineering review identifies candidate parts and explains the differences.

For samples and a quotation

  • Candidate part numbers

    From the selector or engineering review

  • Quantity and project stage

    Prototyping / pilot build / production

  • Required delivery date

    Specify sample and production timing separately

  • Required documentation

    Compliance documents, material declarations or third-party reports

Samples are available for evaluation, and selected parts are free of charge. Our FAE team will be glad to confirm the options for your project. Sales will respond on business days.

Your information will be used only to respond to this support request.

Published replacement reviews View all alternatives

Parameter comparison

Compare selected part numbers

Differences are presented for review; confirm final values and file revisions in each part-specific datasheet.