Gigabit PoE Industrial Area-Scan Camera Reference Design
An illustrative main / interface board design for a GigE Vision gigabit PoE industrial area-scan camera used in production-line inspection, positioning guidance and code reading: images are transmitted over Gigabit Ethernet (1000BASE-T), the camera is powered over the same cable by IEEE 802.3af PoE or from an auxiliary DC 12 ~ 24V supply through the I/O connector; an FPGA / ISP main controller connects to the front-end CMOS image sensor board, with a DDR3 frame buffer and an optocoupler-isolated trigger input and strobe output. This page covers the function, selection notes and available VOOHU parts for 27 component positions.
Illustrative PCB ⇄ Schematic
The illustrative layout shows placement and component positions; click any position to see its selection notes, recommended parts and package. The board view is an illustration neatly arranged by functional zone (not the actual layout) and shows only the camera main / interface board; the RJ45 port and I/O connector sit along the bottom edge, and the CMOS image sensor board connects through the board-to-board connector at the top as an external node.
The 4 Gigabit Ethernet differential pairs are identical, so the diagram shows 1 pair. J1 is a plain RJ45 without magnetics, coupled through the discrete gigabit PoE LAN transformer T1 (WHSG24701D1, 5000 Vrms isolation); the PHY-side pairs are clamped by ESD arrays D1 / D2 (WHALD03G4U) and go to the gigabit PHY U1 (JL2101C-NI), which connects to the FPGA over RGMII. The T1 cable-side center taps bring PoE power out to the bridge rectifier (see the PoE PD chain), and the gas discharge tube G1 diverts surges to chassis ground. Center-tap termination and crystal load capacitor values per the PHY datasheet.
Board bill of materials
Click any row to jump to that position and view its selection notes
| No. | Zone | Position | Ref. | VOOHU category | Recommended part | Availability |
|---|---|---|---|---|---|---|
| 01 | A Gigabit port | RJ45 port (gigabit · PoE powered) | J1 | RJ45 Connectors | SYT561188AB1A1DB4 | VOOHU |
| 02 | A Gigabit port | Gas discharge tube (cable side to chassis) | G1 | GDT | WHGD200V1P0B | VOOHU |
| 03 | A Gigabit port | Gigabit PoE LAN transformer | T1 | Gigabit LAN Transformers | WHSG24701D1 | VOOHU |
| 04 | A Gigabit port | Ethernet ESD array ×2 | D1 D2 | TVS / ESD | WHALD03G4U | VOOHU |
| 05 | A Gigabit port | Gigabit PHY (RGMII) | U1 | Ethernet PHY | JL2101C-NI | VOOHU |
| 06 | A Gigabit port | PHY 25MHz crystal | Y1 | — | — | Non-VOOHU |
| 07 | B PoE PD | PoE input bridge rectifier | D3 | — | — | Non-VOOHU |
| 08 | B PoE PD | PD input TVS | D4 | TVS / ESD | WHTB058VA | VOOHU |
| 09 | B PoE PD | PoE PD controller + flyback PWM | U2 | — | — | Non-VOOHU |
| 10 | B PoE PD | PoE flyback transformer | T2 | PoE Power Transformers | WH13P-12L2 | VOOHU |
| 11 | B PoE PD | Secondary synchronous rectifier | U3 | — | — | Non-VOOHU |
| 12 | B PoE PD | Opto feedback | U4 | — | — | Non-VOOHU |
| 13 | C Trigger I/O | I/O connector (6-pin circular: power + I/O) | J2 | — | — | Non-VOOHU |
| 14 | C Trigger I/O | I/O line ESD ×2 | D5 D6 | TVS / ESD | WHALD30E2B | VOOHU |
| 15 | C Trigger I/O | Opto-isolated input (trigger Line1) | U5 | — | — | Non-VOOHU |
| 16 | C Trigger I/O | Opto-isolated output (strobe Line2) | U6 | — | — | Non-VOOHU |
| 17 | D Core · Imaging | Image sensor board-to-board connector | J3 | — | — | Non-VOOHU |
| 18 | D Core · Imaging | FPGA / ISP main controller | U7 | — | — | Non-VOOHU |
| 19 | D Core · Imaging | DDR3 frame buffer | U8 | — | — | Non-VOOHU |
| 20 | D Core · Imaging | QSPI Flash | U9 | — | — | Non-VOOHU |
| 21 | D Core · Imaging | Main clock oscillator | Y2 | — | — | Non-VOOHU |
| 22 | D Core · Imaging | Sensor power LDO | U10 | — | — | Non-VOOHU |
| 23 | D Core · Imaging | Core supply filter molded inductor ×2 | L1 L2 | Molded Inductors | WHYTA0420 Series | VOOHU |
| 24 | E Power | Power line CMC (auxiliary input EMI) | L3 | Power Line CMC | WHAL-7060A-102T0 | VOOHU |
| 25 | E Power | PoE / auxiliary input ORing diodes | D7 D8 | — | — | Non-VOOHU |
| 26 | E Power | Synchronous buck ×3 (1.0V / 1.5V / 3.3V) | U11 U12 U13 | — | — | Non-VOOHU |
| 27 | E Power | DC-DC molded inductor ×3 | L4 L5 L6 | Molded Inductors | WHYT0630 Series | VOOHU |
Resources & downloads
Board bill of materials
Reference designators, zones, VOOHU categories, recommended parts and availability for all 27 positions. Opens directly in Excel.
Datasheet collection
Datasheet PDFs for the VOOHU parts recommended on this board.
Design files & footprint library
Schematic, PCB, and VOOHU part footprints and 3D models.
Coming soonRequest the machine vision camera reference design full package
Includes the BOM, datasheets for the recommended VOOHU parts and position-by-position selection notes. For selection advice tailored to your power scheme, PoE power class or network connector type, please include it in your requirements. We reply within 24 hours on working days.