EtherCAT Multi-Axis Motion Controller Reference Design
An illustrative EtherCAT master multi-axis motion controller design for packaging, electronics assembly, robot workcells and multi-axis special-purpose machines: DC 24V supply, a 10/100 EtherCAT master port daisy-chaining servo drives and remote I/O slaves, a Gigabit Ethernet port to the host PC / HMI, isolated RS-485 and isolated CAN fieldbuses, and an FPGA extending optocoupler-isolated high-speed digital I/O and RS-422 differential pulse / encoder interfaces. This page covers the function, selection notes and available VOOHU parts for 33 component positions.
Illustrative PCB ⇄ Schematic
The illustrative layout shows placement and component positions; click any position to see its selection notes, recommended parts and package. The board view is an illustration neatly arranged by functional zone (not the actual layout); the EtherCAT master port, host Ethernet port, bus terminals, high-speed I/O terminal and 24V power terminal sit along the bottom edge, and the servo drives and host PC are external nodes.
The EtherCAT master port is standard Fast Ethernet using only 2 pairs (TX / RX); 1 pair is drawn and the other is identical. The plain RJ45 J1 goes through the VOOHU discrete 10/100 LAN transformer T1 (WHS16037TG, 1500 Vrms isolation; switch to the 4800 Vrms WHSH16F01D4 for noisy sites), is clamped on the PHY side by ESD array D1, then reaches the JL1101BR 10/100 PHY, which connects to the SoC MAC over RMII; the EtherCAT master stack runs on the SoC. Center-tap connection, termination and crystal load capacitor values per the PHY datasheet.
Board bill of materials
Click any row to jump to that position and view its selection notes
| No. | Zone | Position | Ref. | VOOHU category | Recommended part | Availability |
|---|---|---|---|---|---|---|
| 01 | A EtherCAT master | RJ45 port (EtherCAT master port) | J1 | RJ45 Connectors | SYT561188AB1A1DB4 | VOOHU |
| 02 | A EtherCAT master | 10/100 LAN transformer (EtherCAT port) | T1 | 10/100 LAN Transformers | WHS16037TG | VOOHU |
| 03 | A EtherCAT master | Ethernet ESD array | D1 | TVS / ESD | WHALD03G4U | VOOHU |
| 04 | A EtherCAT master | EtherCAT master 10/100 PHY | U1 | Ethernet PHY | JL1101BR-NI | VOOHU |
| 05 | A EtherCAT master | PHY 25MHz crystal | Y1 | — | — | Non-VOOHU |
| 06 | B Host Ethernet | RJ45 port (host Gigabit Ethernet) | J2 | RJ45 Connectors | SYT561188AB1A1DB4 | VOOHU |
| 07 | B Host Ethernet | Gigabit LAN transformer | T2 | Gigabit LAN Transformers | WHSG24301GM | VOOHU |
| 08 | B Host Ethernet | Ethernet ESD array ×2 (Gigabit) | D2 D3 | TVS / ESD | WHALD03G4U | VOOHU |
| 09 | B Host Ethernet | Gigabit PHY (RGMII) | U2 | Ethernet PHY | JL2101C-NI | VOOHU |
| 10 | B Host Ethernet | Gigabit PHY crystal | Y2 | — | — | Non-VOOHU |
| 11 | C Fieldbus | Bus terminals (RS-485 / CAN) | J3 J4 | — | — | Non-VOOHU |
| 12 | C Fieldbus | Gas discharge tube (stage 1) | GDT1 GDT2 | GDT | WHGD200V1P0B | VOOHU |
| 13 | C Fieldbus | Bus TVS (stage-2 clamp) | D4 D5 | TVS / ESD | WHALD30E2B | VOOHU |
| 14 | C Fieldbus | Bus differential-line common-mode choke | L1 L2 | Signal Line CMC | WHAC-3225B-510U0 | VOOHU |
| 15 | C Fieldbus | Isolated RS-485 transceiver | U3 | — | — | Non-VOOHU |
| 16 | C Fieldbus | Isolated CAN transceiver | U4 | — | — | Non-VOOHU |
| 17 | D High-speed I/O | High-speed I/O terminal | J5 | — | — | Non-VOOHU |
| 18 | D High-speed I/O | I/O terminal ESD ×2 | D6 D7 | TVS / ESD | WHALD30E2B | VOOHU |
| 19 | D High-speed I/O | High-speed optocoupler (digital I/O isolation) | U5 | — | — | Non-VOOHU |
| 20 | D High-speed I/O | RS-422 differential transceiver | U6 | — | — | Non-VOOHU |
| 21 | E Core | Main processor (multi-core) | U7 | — | — | Non-VOOHU |
| 22 | E Core | FPGA (high-speed I/O extension) | U8 | — | — | Non-VOOHU |
| 23 | E Core | DDR memory | U9 | — | — | Non-VOOHU |
| 24 | E Core | eMMC storage | U10 | — | — | Non-VOOHU |
| 25 | E Core | Main crystal | Y3 | — | — | Non-VOOHU |
| 26 | E Core | Core supply filter molded inductor ×2 | L3 L4 | Molded Inductors | WHYTA0420 Series | VOOHU |
| 27 | F Power | DC 24V input terminal | J6 | — | — | Non-VOOHU |
| 28 | F Power | Input fuse + TVS | F1 D8 | TVS / ESD | WHTB058VA | VOOHU |
| 29 | F Power | Power line common-mode choke (EMI) | L5 | Power Line CMC | WHAL-7060A-102T0 | VOOHU |
| 30 | F Power | Synchronous buck ×2 (24V→5V→3.3V) | U11 U12 | — | — | Non-VOOHU |
| 31 | F Power | DC-DC molded inductor ×2 | L6 L7 | Molded Inductors | WHYT0630 Series | VOOHU |
| 32 | F Power | Push-pull isolated power transformer | T3 | Push-Pull Transformers | WHST06K14A0 | VOOHU |
| 33 | F Power | Push-pull driver + isolated-side LDO | U13 U14 | — | — | Non-VOOHU |
Resources & downloads
Board bill of materials
Reference designators, zones, VOOHU categories, recommended parts and availability for all 33 positions. Opens directly in Excel.
Datasheet collection
Datasheet PDFs for the VOOHU parts recommended on this board.
Design files & footprint library
Schematic, PCB, and VOOHU part footprints and 3D models.
Coming soonRequest the motion controller reference design full package
Includes the BOM, datasheets for the recommended VOOHU parts and position-by-position selection notes. For selection advice tailored to your axis count, Ethernet port configuration or fieldbus protocol, please include it in your requirements. We reply within 24 hours on working days.