Merging Unit (MU) Reference Design
Illustrative reference design of a merging unit (MU) mainboard for the process bus of a smart substation: the AC sampling module digitizes the secondary voltages / currents of conventional instrument transformers through power-frequency CT / PT and synchronous ADCs, and the FPGA frames them per IEC 61850-9-2 and outputs SV point-to-point or over a network to protection, control and metering devices through four 100Base-FX optical ports, while also exchanging GOOSE; IRIG-B time sync drives sampling synchronization, with ≤1 µs synchronization error achieved by FPGA time-keeping. The AC sampling module and power module are not on this board. Each position is marked with the VOOHU part available, recommended part numbers and package pinout.
Illustrative PCB ⇄ Schematic
Illustrative top-side view arranged by functional zone (not the actual layout). Red numbered dots mark positions VOOHU can supply. Click a component on the board, an entry in the index below or a part in the schematic to see recommended parts and package pinouts on the right.
Optical port 1 reference topology: the MAC of FPGA U1 connects over RMII to VOOHU 10/100 PHY U4 (JL1111B-NI, configured for RMII-FIB, i.e. 100Base-FX), whose FX differential transmit / receive pairs go straight to the SFP host connector (defined by SFF-8431 MSA) holding a 100Base-FX optical module; the module control and status lines (MOD_ABS / TX_DISABLE / RX_LOS) go to GPIO, and its 3.3 V is filtered by VOOHU molded inductor L1. Follow the PHY datasheet for the FX termination and bias network; the diagram is illustrative only.
Board bill of materials
Summarized by position; click any row to locate it on the board above.
| No. | Zone | Position | Ref. | VOOHU category | Recommended part | Availability |
|---|---|---|---|---|---|---|
| 01 | A SV Optical 1–2 | SFP cage + host connector (optical port 1) | J1 | SFP Series | WH81-111-Y0016-1 | VOOHU |
| 02 | A SV Optical 1–2 | Optical module supply filter inductor (port 1) | L1 | Molded Inductors | WHYTA0420 Series | VOOHU |
| 03 | A SV Optical 1–2 | 10/100 PHY (optical port 1 · FX mode) | U4 | Ethernet PHY | JL1111B-NI | VOOHU |
| 04 | A SV Optical 1–2 | SFP cage + host connector (optical port 2) | J2 | SFP Series | WH81-111-Y0016-1 | VOOHU |
| 05 | A SV Optical 1–2 | Optical module supply filter inductor (port 2) | L2 | Molded Inductors | WHYTA0420 Series | VOOHU |
| 06 | A SV Optical 1–2 | 10/100 PHY (optical port 2 · FX mode) | U5 | Ethernet PHY | JL1111B-NI | VOOHU |
| 07 | B SV / GOOSE Optical 3–4 | SFP cage + host connector (optical port 3) | J3 | SFP Series | WH81-111-Y0016-1 | VOOHU |
| 08 | B SV / GOOSE Optical 3–4 | Optical module supply filter inductor (port 3) | L3 | Molded Inductors | WHYTA0420 Series | VOOHU |
| 09 | B SV / GOOSE Optical 3–4 | 10/100 PHY (optical port 3 · FX mode) | U6 | Ethernet PHY | JL1111B-NI | VOOHU |
| 10 | B SV / GOOSE Optical 3–4 | SFP cage + host connector (optical port 4) | J4 | SFP Series | WH81-111-Y0016-1 | VOOHU |
| 11 | B SV / GOOSE Optical 3–4 | Optical module supply filter inductor (port 4) | L4 | Molded Inductors | WHYTA0420 Series | VOOHU |
| 12 | B SV / GOOSE Optical 3–4 | 10/100 PHY (optical port 4 · FX mode) | U7 | Ethernet PHY | JL1111B-NI | VOOHU |
| 13 | C IRIG-B time sync | IRIG-B time-sync terminal (RS-485 differential B code) | J5 | — | — | Non-VOOHU |
| 14 | C IRIG-B time sync | IRIG-B time-sync line CMC | L5 | Signal Line CMC | WHAC-4532A-510U0 | VOOHU |
| 15 | C IRIG-B time sync | IRIG-B time-sync ESD / TVS | D1 | TVS / ESD | WHALD30E2B | VOOHU |
| 16 | C IRIG-B time sync | IRIG-B isolated receiver (RS-485) | U8 | — | — | Non-VOOHU |
| 17 | C IRIG-B time sync | Push-pull driver + rectifier / LDO | U9 | — | — | Non-VOOHU |
| 18 | C IRIG-B time sync | Push-pull isolation transformer | T1 | Push-Pull Transformers | WHST06Q06A0 | VOOHU |
| 19 | D FPGA / CPU | FPGA (SV framing + sync) | U1 | — | — | Non-VOOHU |
| 20 | D FPGA / CPU | Management CPU | U2 | — | — | Non-VOOHU |
| 21 | D FPGA / CPU | Synchronous ADC interface (AC module) | U3 | — | — | Non-VOOHU |
| 22 | E Module Power | Backplane power (+24 V from power module) | J6 | — | — | Non-VOOHU |
| 23 | E Module Power | Input power-line common-mode choke | L6 | Power Line CMC | WHAL-7060A-701T0 | VOOHU |
| 24 | E Module Power | Buck converter (24 V → 5 V) | U10 | — | — | Non-VOOHU |
| 25 | E Module Power | Buck (5 V → 3.3 V / FPGA core) | U11 | — | — | Non-VOOHU |
| 26 | E Module Power | Molded inductors ×2 (DC-DC) | L7 L8 | Molded Inductors | WHYT0630 Series | VOOHU |
Resources & downloads
Board bill of materials
Reference designators, zones, VOOHU categories, recommended parts and availability for all 26 positions. Opens directly in Excel.
Datasheet collection
Datasheet PDFs for the VOOHU parts recommended on this board.
Design files & footprint library
Schematic, PCB, and VOOHU part footprints and 3D models.
Coming soonRequest the full merging unit reference design packagefull package
Includes the board position list, datasheets of recommended VOOHU parts and per-position selection notes. For advice on your optical port count, point-to-point / networked mode or time-sync method (IRIG-B / IEEE 1588), describe them in the request. We reply within 24 hours on working days.