Dante Network Audio Interface Reference Design
Illustrative design of a Dante / AES67 network audio interface box (2 in / 2 out) for live sound, meeting rooms, broadcast and fixed installation: Gigabit Ethernet connection to the audio network, IEEE 802.3af PoE power over the same cable; 2 mic / instrument inputs (XLR / 6.35 mm combo jacks, switchable +48V phantom power, preamp then ADC) and 2 line outputs (DAC, then audio-transformer isolation to a balanced output on XLR male connectors); a push-pull transformer generates the bipolar analog supply for the preamps and line drivers. This page gives the function, selection notes and available VOOHU part numbers for 32 component positions.
Illustrative PCB ⇄ Schematic
The illustrative layout shows placement and component positions; click any position for selection notes, recommended parts and package. The board is an illustration arranged by functional zone (not an actual layout) and shows only the interface main board; the RJ45 port, mic / instrument combo input jacks and line-output XLR connectors sit on the bottom edge, and microphones, instruments and the downstream mixer / amplifier are external nodes.
The 4 Gigabit Ethernet pairs (A / B / C / D) are identical, so only 1 pair is drawn. RJ45 J1 is a latching RJ45 without magnetics, coupled through the discrete Gigabit PoE LAN transformer T1 (WHSG24701D1); on the PHY side the pairs are clamped by two ESD arrays D1/D2 (WHALD03G4U, 2 pairs each) before the Gigabit PHY U1 (JL2101C-NE), which connects to the Dante / AES67 network audio processor U8 over RGMII. The cable-side center taps of all four pairs of T1 deliver PoE power to the bridge rectifier (powered in Mode A or B, see the PoE PD chain). Center-tap termination and crystal load capacitor values follow the PHY datasheet.
Board bill of materials
Click any row to jump to that position and view its selection notes
| No. | Zone | Position | Ref. | VOOHU category | Recommended part | Availability |
|---|---|---|---|---|---|---|
| 01 | A Ethernet port | RJ45 port (PoE powered · latching) | J1 | RJ45 Connectors | WHA9080001051AB35 | VOOHU |
| 02 | A Ethernet port | Gigabit PoE LAN transformer | T1 | Gigabit LAN Transformers | WHSG24701D1 | VOOHU |
| 03 | A Ethernet port | Ethernet ESD array ×2 | D1 D2 | TVS / ESD | WHALD03G4U | VOOHU |
| 04 | A Ethernet port | Gigabit PHY (RGMII) | U1 | Ethernet PHY | JL2101C-NE | VOOHU |
| 05 | A Ethernet port | PHY 25MHz crystal | Y1 | — | — | Non-VOOHU |
| 06 | B PoE PD | PoE input bridge rectifier | D3 | — | — | Non-VOOHU |
| 07 | B PoE PD | PD input TVS | D4 | TVS / ESD | WHTB058VA | VOOHU |
| 08 | B PoE PD | PoE PD controller + flyback PWM | U2 | — | — | Non-VOOHU |
| 09 | B PoE PD | PoE flyback transformer | T2 | PoE Power Transformers | WH13P-12L2 | VOOHU |
| 10 | B PoE PD | Secondary synchronous rectifier | U3 | — | — | Non-VOOHU |
| 11 | B PoE PD | Opto feedback | U4 | — | — | Non-VOOHU |
| 12 | C Mic input | XLR / TRS combo input jack ×2 | J2 J3 | — | — | Non-VOOHU |
| 13 | C Mic input | Mic input common-mode choke ×2 | L1 L2 | Signal Line CMC | WHAC-3225B-510U0 | VOOHU |
| 14 | C Mic input | Phantom feed and switch ×2 | Q1 Q2 | — | — | Non-VOOHU |
| 15 | C Mic input | Mic input ESD ×2 | D5 D6 | TVS / ESD | WHALD30E2B | VOOHU |
| 16 | C Mic input | Mic / instrument preamp ×2 | U5 U6 | — | — | Non-VOOHU |
| 17 | D Line output | Line output driver | U7 | — | — | Non-VOOHU |
| 18 | D Line output | Line-output audio transformer ×2 | T3 T4 | Audio Transformer | WHTT6010 | VOOHU |
| 19 | D Line output | Line-output ESD ×2 | D7 D8 | TVS / ESD | WHALD30E2B | VOOHU |
| 20 | D Line output | XLR line-output connector ×2 | J4 J5 | — | — | Non-VOOHU |
| 21 | E Audio core | Dante / AES67 network audio processor | U8 | — | — | Non-VOOHU |
| 22 | E Audio core | SPI Flash | U9 | — | — | Non-VOOHU |
| 23 | E Audio core | Audio ADC (2-channel) | U10 | — | — | Non-VOOHU |
| 24 | E Audio core | Audio DAC (2-channel) | U11 | — | — | Non-VOOHU |
| 25 | E Audio core | Audio master clock (VCXO) | Y2 | — | — | Non-VOOHU |
| 26 | F Power | Synchronous buck ×2 (+5V / +3V3) | U12 U13 | — | — | Non-VOOHU |
| 27 | F Power | DC-DC molded inductor ×2 | L3 L4 | Molded Inductors | WHYTA0530 Series | VOOHU |
| 28 | F Power | +48V phantom power boost controller | U14 | — | — | Non-VOOHU |
| 29 | F Power | +48V boost inductor | L5 | Molded Inductors | WHYT0630 Series | VOOHU |
| 30 | F Power | Push-pull driver | U15 | — | — | Non-VOOHU |
| 31 | F Power | Push-pull power transformer (bipolar analog supply) | T5 | Push-Pull Transformers | WHST06K14A0 | VOOHU |
| 32 | F Power | ± LDO | U16 | — | — | Non-VOOHU |
Resources & downloads
Board bill of materials
Reference designators, zones, VOOHU categories, recommended parts and availability for all 32 positions. Opens directly in Excel.
Datasheet collection
Datasheet PDFs for the VOOHU parts recommended on this board.
Design files & footprint library
Schematic, PCB, and VOOHU part footprints and 3D models.
Coming soonRequest the full network audio interface reference design packagefull package
Includes the BOM, datasheets of the recommended VOOHU parts and position-by-position selection notes. If you need selection advice for your channel count, PoE power class or input / output interface type, please describe it in your request. We reply within 24 hours on working days.