Security PoE Switch Reference Design
Illustrative design of a surveillance PoE switch for the transmission layer of video surveillance, powering and aggregating IP cameras: 8 × 10/100/1000BASE-T PoE ports (power sourcing equipment, PSE, IEEE 802.3af / at) + 2 × 1000BASE-X SFP uplinks to the NVR / aggregation switch, JL6110-PI 8+2-port gigabit switch IC (integrated PHYs), 8-channel PSE controller + PoE management MCU, DC 48 ~ 57V input (from a 52V power module or adapter) feeding the PoE bus directly. This page lists the function, selection notes and available VOOHU part numbers for all 25 component positions.
Illustrative PCB ⇄ Schematic
Use the illustrative layout to see placement and component positions; click any position for selection notes, recommended parts and package. The board is an illustrative arrangement by functional zone (not the actual layout); the 8 PoE ports, 2 SFP ports and the power input jack sit on the bottom edge, the switch IC is in the top core zone, and the PSE controller feeds each port's transformer cable-side center tap from the PoE bus.
Ports P1–P4 are identical; one port and one differential pair are shown (4 pairs per gigabit port, A/B/C/D identical). The JL6110-PI integrates gigabit PHYs; the pairs are clamped on the PHY side by ESD arrays D5–D12 (WHALD03G4U, 2 per port) and enter VOOHU gigabit PoE+ LAN transformers T1–T4 (WHSG24706-1PTG, PoE+ ≤ 720 mA, one per port); the cable side goes through RJ45 1×4 J1 (no integrated magnetics) to the IP cameras. The PSE port output is injected at the cable-side center taps (+ and − on the center taps of two different pairs); port TVS D1–D4 (WHTB058VA) sits across the port output, and gas discharge tubes G1–G4 (WHGD200V1P0B) discharge surges from the cable side to chassis ground. PHY-side center taps and Bob-Smith termination per the JL6110 and transformer datasheets.
Board bill of materials
Click any row to jump to that position and view its selection notes
| No. | Zone | Position | Ref. | VOOHU category | Recommended part | Availability |
|---|---|---|---|---|---|---|
| 01 | A PoE P1–P4 | RJ45 1×4 ports (P1–P4) | J1 | RJ45 Connectors | SYT561488AB1A3DY1027 | VOOHU |
| 02 | A PoE P1–P4 | Gas discharge tube ×4 (P1–P4) | G1 G2 G3 G4 | GDT | WHGD200V1P0B | VOOHU |
| 03 | A PoE P1–P4 | PoE port TVS ×4 (P1–P4) | D1 D2 D3 D4 | TVS / ESD | WHTB058VA | VOOHU |
| 04 | A PoE P1–P4 | Gigabit PoE+ LAN transformer ×4 (P1–P4) | T1 T2 T3 T4 | Gigabit LAN Transformers | WHSG24706-1PTG | VOOHU |
| 05 | A PoE P1–P4 | Ethernet ESD arrays ×8 (P1–P4) | D5 D6 D7 D8 D9 D10 D11 D12 | TVS / ESD | WHALD03G4U | VOOHU |
| 06 | B PoE P5–P8 | RJ45 1×4 ports (P5–P8) | J2 | RJ45 Connectors | SYT561488AB1A3DY1027 | VOOHU |
| 07 | B PoE P5–P8 | Gas discharge tube ×4 (P5–P8) | G5 G6 G7 G8 | GDT | WHGD200V1P0B | VOOHU |
| 08 | B PoE P5–P8 | PoE port TVS ×4 (P5–P8) | D13 D14 D15 D16 | TVS / ESD | WHTB058VA | VOOHU |
| 09 | B PoE P5–P8 | Gigabit PoE+ LAN transformer ×4 (P5–P8) | T5 T6 T7 T8 | Gigabit LAN Transformers | WHSG24706-1PTG | VOOHU |
| 10 | B PoE P5–P8 | Ethernet ESD arrays ×8 (P5–P8) | D17 D18 D19 D20 D21 D22 D23 D24 | TVS / ESD | WHALD03G4U | VOOHU |
| 11 | C PSE power control | PSE controller (8-ch, IEEE 802.3af / at) | U1 | — | — | Non-VOOHU |
| 12 | C PSE power control | PoE mgmt MCU | U2 | — | — | Non-VOOHU |
| 13 | D Fiber uplinks | SFP cage + 20-pin connector ×2 (uplinks) | J3 J4 | SFP Cage / SFP Connectors | WHSFP00211W018 | VOOHU |
| 14 | D Fiber uplinks | SFP supply filter molded inductor ×2 | L1 L2 | Molded Inductors | WHYTA0420 Series | VOOHU |
| 15 | E Switch Core | 8+2-port Gigabit switch IC | U3 | Ethernet Switch ICs | JL6110-PI | VOOHU |
| 16 | E Switch Core | Switch IC reference crystal | Y1 | — | — | Non-VOOHU |
| 17 | E Switch Core | Config EEPROM | U4 | — | — | Non-VOOHU |
| 18 | E Switch Core | Mode DIP switch (optional) | S1 | — | — | Non-VOOHU |
| 19 | E Switch Core | Switch IC supply filter molded inductor ×2 | L3 L4 | Molded Inductors | WHYTA0420 Series | VOOHU |
| 20 | F Power | DC 48 ~ 57V power input jack | J5 | — | — | Non-VOOHU |
| 21 | F Power | Input fuse | F1 | — | — | Non-VOOHU |
| 22 | F Power | Input TVS | D25 | TVS / ESD | WHTB058VA | VOOHU |
| 23 | F Power | Power line common-mode choke (EMI) | L5 | Power Line CMC | WHAL-9070A-301T0 | VOOHU |
| 24 | F Power | Wide-input sync buck ×2 (52V→3.3V→1.1V) | U5 U6 | — | — | Non-VOOHU |
| 25 | F Power | DC-DC molded inductor ×2 | L6 L7 | Molded Inductors | WHYT1030 Series | VOOHU |
Resources & downloads
Board bill of materials
Reference designators, zones, VOOHU categories, recommended parts and availability for all 25 positions. Opens directly in Excel.
Datasheet collection
Datasheet PDFs for the VOOHU parts recommended on this board.
Design files & footprint library
Schematic, PCB, and VOOHU part footprints and 3D models.
Coming soonRequest the complete Security PoE Switch reference design packagefull package
Includes the BOM, datasheets of the recommended VOOHU parts and position-by-position selection notes. For advice on your port count, PoE class (af / at) or uplink type, describe it in the requirements field. We reply within 24 hours on working days.