Outdoor Network PTZ Speed Dome Reference Design
Illustrative design of the main board of an outdoor network PTZ speed dome for campus, road, perimeter and plaza surveillance: Gigabit Ethernet carries the video stream and the same cable delivers IEEE 802.3at (PoE+) power, with an auxiliary DC 12V input as an alternative; the IPC SoC connects to an integrated zoom camera module and drives two stepper motors for pan and tilt, while RS-485 (PELCO-D / P) control, alarm input / output and audio input / output are brought out through the pigtail cable. This page covers 35 component positions with their functions, selection notes and the VOOHU part numbers available.
Illustrative PCB ⇄ Schematic
The illustrative layout shows the placement and component positions; click any position to see selection notes, recommended parts and package. The board is an illustration arranged by functional zone (not the actual layout) and shows only the PTZ dome main board; the RJ45 port, pan / tilt motor connector, pigtail connector and DC jack sit on the bottom edge, and the integrated zoom camera module connects through the camera-module connector at the top. The camera module and the pan / tilt motors are external nodes.
The 4 Gigabit Ethernet pairs are identical; only 1 pair is drawn. RJ45 J1 is a plain RJ45 without magnetics, coupled through the discrete Gigabit PoE+ LAN transformer T1 (WHSG24706-1PTG, PoE+ ≤ 720 mA); the PHY-side pairs are clamped by ESD arrays D1 / D2 (WHALD03G4U) and connect to the Gigabit PHY U1 (JL2101C-NI), which connects to the IPC SoC over RGMII. The T1 line-side center taps bring PoE+ power to the bridge rectifier (see the PoE+ PD chain), and the gas discharge tube G1 discharges surges from the outdoor cable to chassis ground. Center-tap termination and crystal load capacitor values per the PHY datasheet.
Board bill of materials
Click any row to jump to that position and view its selection notes
| No. | Zone | Position | Ref. | VOOHU category | Recommended part | Availability |
|---|---|---|---|---|---|---|
| 01 | A Gigabit port | RJ45 port (Gigabit · PoE+ powered) | J1 | RJ45 Connectors | SYT561188AB1A1DB4 | VOOHU |
| 02 | A Gigabit port | Gas discharge tube (cable side to chassis) | G1 | GDT | WHGD200V1P0B | VOOHU |
| 03 | A Gigabit port | Gigabit PoE+ LAN transformer | T1 | Gigabit LAN Transformers | WHSG24706-1PTG | VOOHU |
| 04 | A Gigabit port | Ethernet ESD array ×2 | D1 D2 | TVS / ESD | WHALD03G4U | VOOHU |
| 05 | A Gigabit port | Gigabit PHY (RGMII) | U1 | Ethernet PHY | JL2101C-NI | VOOHU |
| 06 | A Gigabit port | PHY 25MHz crystal | Y1 | — | — | Non-VOOHU |
| 07 | B PoE+ PD | PoE input bridge rectifier | D3 | — | — | Non-VOOHU |
| 08 | B PoE+ PD | PD input TVS | D4 | TVS / ESD | WHTB058VA | VOOHU |
| 09 | B PoE+ PD | PoE+ PD controller + flyback PWM | U2 | — | — | Non-VOOHU |
| 10 | B PoE+ PD | PoE flyback transformer | T2 | PoE Power Transformers | WH13P-12H5 | VOOHU |
| 11 | B PoE+ PD | Secondary synchronous rectifier | U3 | — | — | Non-VOOHU |
| 12 | B PoE+ PD | Opto feedback | U4 | — | — | Non-VOOHU |
| 13 | C Pan / Tilt Drive | Pan / tilt stepper motor driver ×2 | U5 U6 | — | — | Non-VOOHU |
| 14 | C Pan / Tilt Drive | Pan / tilt motor & home-Hall connector | J2 | — | — | Non-VOOHU |
| 15 | D Control I/O | Pigtail connector (RS-485 / alarm / audio) | J3 | — | — | Non-VOOHU |
| 16 | D Control I/O | RS-485 gas discharge tube (primary) | G2 | GDT | WHGD090V1P0B | VOOHU |
| 17 | D Control I/O | RS-485 bus TVS (secondary clamp) | D5 | TVS / ESD | WHALD30E2B | VOOHU |
| 18 | D Control I/O | RS-485 differential-line common mode choke | L1 | Signal Line CMC | WHAC-4532A-601ZP0 | VOOHU |
| 19 | D Control I/O | RS-485 transceiver (PELCO-D / P) | U7 | — | — | Non-VOOHU |
| 20 | D Control I/O | Alarm input ESD | D6 | TVS / ESD | WHALD30E2B | VOOHU |
| 21 | D Control I/O | Alarm input optocoupler | U8 | — | — | Non-VOOHU |
| 22 | D Control I/O | Alarm output relay | K1 | — | — | Non-VOOHU |
| 23 | D Control I/O | Audio line isolation transformer ×2 (in / out) | T3 T4 | Audio Transformer | WHTT4001 | VOOHU |
| 24 | D Control I/O | Audio codec | U9 | — | — | Non-VOOHU |
| 25 | E Core · Camera Module | Camera-module connector (zoom lens + image sensor) | J4 | — | — | Non-VOOHU |
| 26 | E Core · Camera Module | IPC SoC (ISP + video encoding) | U10 | — | — | Non-VOOHU |
| 27 | E Core · Camera Module | DDR memory | U11 | — | — | Non-VOOHU |
| 28 | E Core · Camera Module | SPI NAND Flash | U12 | — | — | Non-VOOHU |
| 29 | E Core · Camera Module | Main clock oscillator | Y2 | — | — | Non-VOOHU |
| 30 | E Core · Camera Module | Core supply filter molded inductor ×2 | L2 L3 | Molded Inductors | WHYTA0420 Series | VOOHU |
| 31 | F Power | DC 12V auxiliary power jack | J5 | — | — | Non-VOOHU |
| 32 | F Power | Power line common mode choke (input EMI) | L4 | Power Line CMC | WHAL-9070A-301T0 | VOOHU |
| 33 | F Power | PoE / DC input ORing diodes | D7 D8 | — | — | Non-VOOHU |
| 34 | F Power | Synchronous buck ×3 (core / DDR / 3.3V) | U13 U14 U15 | — | — | Non-VOOHU |
| 35 | F Power | DC-DC molded inductor ×3 | L5 L6 L7 | Molded Inductors | WHYT0630 Series | VOOHU |
Resources & downloads
Board bill of materials
Reference designators, zones, VOOHU categories, recommended parts and availability for all 35 positions. Opens directly in Excel.
Datasheet collection
Datasheet PDFs for the VOOHU parts recommended on this board.
Design files & footprint library
Schematic, PCB, and VOOHU part footprints and 3D models.
Coming soonRequest the full PTZ dome reference design packagefull package
Includes the BOM, datasheets of the recommended VOOHU parts and position-by-position selection notes. If you need selection advice for your power scheme, PoE power class, outdoor surge protection or audio interface, describe it in your requirements. We reply within 24 hours on working days.