Outdoor PoE Bullet IP Camera Reference Design
Illustrative main-board design for an outdoor PoE bullet IP camera (IPC) used in campus, road and perimeter surveillance: Gigabit Ethernet (1000BASE-T) uplinks the video stream and the same cable delivers IEEE 802.3at PoE power (802.3af compatible), with a DC 12V backup input as an alternative; an image SoC connects to the front-end CMOS sensor board, with microSD local storage, an opto-isolated alarm input / PhotoMOS alarm output, optional audio in / out, an IR illuminator constant-current driver and IR-CUT day/night switching. This page lists the function, selection notes and available VOOHU part numbers for all 33 positions.
Illustrative PCB ⇄ Schematic
Use the illustrative layout to see placement and part positions; click any position for selection notes, recommended parts and package. The board is an illustrative arrangement by functional zone (not the actual layout) and shows only the camera main board; the RJ45 port, pigtail I/O and DC jack sit on the bottom edge, while the CMOS image sensor board (via the board-to-board connector at the top) and the IR illuminator board (via its connector) are external nodes.
The four Gigabit Ethernet pairs are identical; only one is drawn. RJ45 J1 is a plain RJ45 without magnetics, coupled through the discrete Gigabit PoE+ LAN transformer T1 (WHSG24706-1PTG, PoE+ ≤ 720 mA); the PHY-side pairs are clamped by ESD arrays D1 / D2 (WHALD03G4U) before the Gigabit PHY U1 (JL2101C-NI), which connects to the image SoC over RGMII. T1's line-side center taps carry PoE power to the bridge rectifier (see the PoE PD chain), and gas discharge tube G1 diverts surges from the outdoor cable to chassis ground. Center-tap termination and crystal load capacitor values per the PHY datasheet.
Board bill of materials
Click any row to jump to that position and view its selection notes
| No. | Zone | Position | Ref. | VOOHU category | Recommended part | Availability |
|---|---|---|---|---|---|---|
| 01 | A Gigabit PoE Port | RJ45 port (gigabit · PoE powered) | J1 | RJ45 Connectors | SYT561188AB1A1DB4 | VOOHU |
| 02 | A Gigabit PoE Port | Gas discharge tube (cable side to chassis) | G1 | GDT | WHGD200V1P0B | VOOHU |
| 03 | A Gigabit PoE Port | Gigabit PoE+ LAN transformer | T1 | Gigabit LAN Transformers | WHSG24706-1PTG | VOOHU |
| 04 | A Gigabit PoE Port | Ethernet ESD array ×2 | D1 D2 | TVS / ESD | WHALD03G4U | VOOHU |
| 05 | A Gigabit PoE Port | Gigabit PHY (RGMII) | U1 | Ethernet PHY | JL2101C-NI | VOOHU |
| 06 | A Gigabit PoE Port | PHY 25MHz crystal | Y1 | — | — | Non-VOOHU |
| 07 | B PoE PD | PoE input bridge rectifier | D3 | — | — | Non-VOOHU |
| 08 | B PoE PD | PD input TVS | D4 | TVS / ESD | WHTB058VA | VOOHU |
| 09 | B PoE PD | PoE PD controller + flyback PWM | U2 | — | — | Non-VOOHU |
| 10 | B PoE PD | PoE flyback transformer | T2 | PoE Power Transformers | WH13P-12H5 | VOOHU |
| 11 | B PoE PD | Secondary synchronous rectifier | U3 | — | — | Non-VOOHU |
| 12 | B PoE PD | Opto feedback | U4 | — | — | Non-VOOHU |
| 13 | C Alarm · Audio | Pigtail I/O connector (alarm / audio) | J2 | — | — | Non-VOOHU |
| 14 | C Alarm · Audio | Alarm line ESD ×2 | D5 D6 | TVS / ESD | WHALD30E2B | VOOHU |
| 15 | C Alarm · Audio | Optically isolated alarm input | U5 | — | — | Non-VOOHU |
| 16 | C Alarm · Audio | Alarm output (PhotoMOS relay) | K1 | — | — | Non-VOOHU |
| 17 | C Alarm · Audio | Audio isolation transformer ×2 (in / out) | T3 T4 | Audio Transformer | WHTT4001 | VOOHU |
| 18 | D Core · Imaging | Image sensor board-to-board connector | J3 | — | — | Non-VOOHU |
| 19 | D Core · Imaging | Image SoC (ISP + video encoding) | U6 | — | — | Non-VOOHU |
| 20 | D Core · Imaging | DDR memory | U7 | — | — | Non-VOOHU |
| 21 | D Core · Imaging | SPI NAND / NOR Flash | U8 | — | — | Non-VOOHU |
| 22 | D Core · Imaging | Main clock oscillator | Y2 | — | — | Non-VOOHU |
| 23 | D Core · Imaging | microSD card socket | J4 | SD Card Sockets | WHTF190T123101W | VOOHU |
| 24 | D Core · Imaging | IR-CUT driver (H-bridge) | U9 | — | — | Non-VOOHU |
| 25 | D Core · Imaging | Core supply filter molded inductor ×2 | L1 L2 | Molded Inductors | WHYTA0420 Series | VOOHU |
| 26 | E Power · IR | DC 12V backup power jack | J5 | — | — | Non-VOOHU |
| 27 | E Power · IR | Power line CMC (DC input EMI) | L3 | Power Line CMC | WHAL-7060A-102T0 | VOOHU |
| 28 | E Power · IR | PoE / DC input ORing diodes | D7 D8 | — | — | Non-VOOHU |
| 29 | E Power · IR | Synchronous buck ×3 (core / DDR / 3.3V) | U10 U11 U12 | — | — | Non-VOOHU |
| 30 | E Power · IR | DC-DC molded inductor ×3 | L4 L5 L6 | Molded Inductors | WHYT0630 Series | VOOHU |
| 31 | E Power · IR | IR illuminator LED constant-current driver | U13 | — | — | Non-VOOHU |
| 32 | E Power · IR | IR LED driver molded inductor | L7 | Molded Inductors | WHYTA0530 Series | VOOHU |
| 33 | E Power · IR | IR illuminator board connector | J6 | — | — | Non-VOOHU |
Resources & downloads
Board bill of materials
Reference designators, zones, VOOHU categories, recommended parts and availability for all 33 positions. Opens directly in Excel.
Datasheet collection
Datasheet PDFs for the VOOHU parts recommended on this board.
Design files & footprint library
Schematic, PCB, and VOOHU part footprints and 3D models.
Coming soonRequest the full Bullet IPC reference design packagefull package
Includes the BOM, datasheets for the recommended VOOHU parts and position-by-position selection notes. If you need advice for your PoE power class, port type, surge-protection requirements or audio interface, describe it in your request. We reply within 24 hours on working days.