Face Recognition Access Control Terminal Reference Design
Illustrative mainboard design of a face recognition access control terminal for campus, building and residential entrances: powered over the network cable by IEEE 802.3af PoE, or from DC 12V (ORing, either source); Fast Ethernet (100BASE-TX) to the access control platform; an AI SoC takes a dual camera (visible + infrared) for liveness detection and face matching and drives a MIPI display and touch panel; Wiegand and RS-485 for card readers, a relay dry contact for the door lock, opto-isolated door sensor and exit button inputs, and a speaker for voice prompts. This page lists the function, selection notes and available VOOHU parts for 36 component positions.
Illustrative PCB ⇄ Schematic
The illustrative layout shows placement and part positions; click any position to view its selection notes, recommended parts and package. The board is an illustrative arrangement by functional zone (not the actual layout) and shows only the terminal mainboard; the RJ45 port, the card reader / door terminal blocks and the DC 12V power terminal sit on the bottom edge, while the display, dual camera modules and speaker connect through FPC / connectors at the top as external nodes.
The TX / RX differential pairs of Fast Ethernet are identical; only one pair is drawn. RJ45 J1 is a plain RJ45 without magnetics, coupled through the discrete PoE LAN transformer T1 (WHSG24701D1, 100/1000 Base-T, isolation 5000 Vrms); the PHY-side pairs are clamped by ESD array D1 (WHALD03G4U) before the 10/100 PHY U1 (JL1101BR-NI), which connects to the SoC over RMII. The cable-side center taps of T1 bring out PoE power to the bridge rectifier (see the PoE PD chain), and gas discharge tube G1 diverts surges to chassis ground. Center-tap termination and crystal load capacitor values per the PHY datasheet.
Board bill of materials
Click any row to jump to that position and view its selection notes
| No. | Zone | Position | Ref. | VOOHU category | Recommended part | Availability |
|---|---|---|---|---|---|---|
| 01 | A Fast Ethernet | RJ45 port (Fast Ethernet · PoE powered) | J1 | RJ45 Connectors | SYT561188AB1A1DB4 | VOOHU |
| 02 | A Fast Ethernet | Gas discharge tube (cable side to chassis) | G1 | GDT | WHGD200V1P0B | VOOHU |
| 03 | A Fast Ethernet | PoE LAN transformer | T1 | Gigabit LAN Transformers | WHSG24701D1 | VOOHU |
| 04 | A Fast Ethernet | Ethernet ESD array | D1 | TVS / ESD | WHALD03G4U | VOOHU |
| 05 | A Fast Ethernet | 10/100 PHY (RMII) | U1 | Ethernet PHY | JL1101BR-NI | VOOHU |
| 06 | A Fast Ethernet | PHY 25MHz crystal | Y1 | — | — | Non-VOOHU |
| 07 | B PoE PD | PoE input bridge rectifier | D2 | — | — | Non-VOOHU |
| 08 | B PoE PD | PD input TVS | D3 | TVS / ESD | WHTB058VA | VOOHU |
| 09 | B PoE PD | PoE PD controller + flyback PWM | U2 | — | — | Non-VOOHU |
| 10 | B PoE PD | PoE flyback transformer | T2 | PoE Power Transformers | WH13P-12L2 | VOOHU |
| 11 | B PoE PD | Secondary synchronous rectifier | U3 | — | — | Non-VOOHU |
| 12 | B PoE PD | Opto feedback | U4 | — | — | Non-VOOHU |
| 13 | C Reader · RS-485 | Card reader terminal block (Wiegand / RS-485) | J2 | — | — | Non-VOOHU |
| 14 | C Reader · RS-485 | Reader line ESD ×2 (Wiegand / RS-485) | D4 D5 | TVS / ESD | WHALD30E2B | VOOHU |
| 15 | C Reader · RS-485 | Wiegand interface buffer | U5 | — | — | Non-VOOHU |
| 16 | C Reader · RS-485 | RS-485 bus common-mode choke | L1 | Signal Line CMC | WHAC-4532A-601ZP0 | VOOHU |
| 17 | C Reader · RS-485 | RS-485 transceiver | U6 | — | — | Non-VOOHU |
| 18 | D Lock · Door sensor | Door terminal block (lock / door sensor / exit button) | J3 | — | — | Non-VOOHU |
| 19 | D Lock · Door sensor | Door sensor / exit button input ESD | D6 | TVS / ESD | WHALD30E2B | VOOHU |
| 20 | D Lock · Door sensor | Opto-isolated input | U7 | — | — | Non-VOOHU |
| 21 | D Lock · Door sensor | Lock relay + driver | K1 | — | — | Non-VOOHU |
| 22 | E Core · Display | AI SoC (face recognition) | U8 | — | — | Non-VOOHU |
| 23 | E Core · Display | DDR memory | U9 | — | — | Non-VOOHU |
| 24 | E Core · Display | eMMC storage | U10 | — | — | Non-VOOHU |
| 25 | E Core · Display | Display FPC connector (MIPI DSI · touch · backlight) | J4 | — | — | Non-VOOHU |
| 26 | E Core · Display | Touch I²C ESD array | D7 | TVS / ESD | WHALD03G4U | VOOHU |
| 27 | E Core · Display | Backlight boost driver | U11 | — | — | Non-VOOHU |
| 28 | E Core · Display | Backlight boost inductor | L4 | Molded Inductors | WHYTA0530 Series | VOOHU |
| 29 | E Core · Display | Dual camera FPC connector ×2 | J5 J6 | — | — | Non-VOOHU |
| 30 | E Core · Display | Core supply filter molded inductor ×2 | L2 L3 | Molded Inductors | WHYTA0420 Series | VOOHU |
| 31 | E Core · Display | Audio amplifier · speaker connector | J8 U15 | — | — | Non-VOOHU |
| 32 | F Power | DC 12V power terminal | J7 | — | — | Non-VOOHU |
| 33 | F Power | Power-line CMC (DC 12V input EMI) | L5 | Power Line CMC | WHAL-7060A-102T0 | VOOHU |
| 34 | F Power | PoE / DC 12V input ORing diodes | D8 D9 | — | — | Non-VOOHU |
| 35 | F Power | Synchronous buck ×3 (SoC core / DDR / 3.3V) | U12 U13 U14 | — | — | Non-VOOHU |
| 36 | F Power | DC-DC molded inductor ×3 | L6 L7 L8 | Molded Inductors | WHYTA0530 Series | VOOHU |
Resources & downloads
Board bill of materials
Reference designators, zones, VOOHU categories, recommended parts and availability for all 36 positions. Opens directly in Excel.
Datasheet collection
Datasheet PDFs for the VOOHU parts recommended on this board.
Design files & footprint library
Schematic, PCB, and VOOHU part footprints and 3D models.
Coming soonRequest the full Face Access Control Reference Design packagefull package
Includes the BOM, datasheets of the recommended VOOHU parts and position-by-position selection notes. If you need selection advice for your power scheme, PoE power class or card reader / door lock interfaces, describe it in the request. We reply within 24 hours on working days.