IP Video Door Station Reference Design
An illustrative mainboard design for an IP video door station used for building / campus access control: audio, video and SIP signaling run over Fast Ethernet (100BASE-TX), the unit is powered over the same cable by IEEE 802.3af PoE or from an auxiliary DC 12V terminal; a video SoC captures and encodes the camera module, its built-in audio codec drives the microphone and speaker, and an optional external audio line is isolated by audio transformers; front-panel keypad / card-reader interfaces, door-contact / exit-button inputs and a lock relay output complete the board. This page covers the function, selection notes and available VOOHU parts for 35 component positions.
Illustrative PCB ⇄ Schematic
The illustrative layout shows placement and part positions; click any position to view selection notes, recommended parts and package. The board is an illustrative arrangement by functional zone (not the actual layout) and shows only the door-station mainboard; the RJ45 port, audio and access terminals and the DC terminal sit on the bottom edge, while the camera module, front-panel keypad / card-reader module, microphone and speaker are external nodes.
The TX / RX differential pairs of Fast Ethernet are identical, so only one pair is drawn. RJ45 J1 is a plain RJ45 without magnetics, coupled through the discrete PoE LAN transformer T1 (WHSG24701D1, 5000 Vrms isolation): data uses only the TX / RX pairs, and the two spare pairs only supply power through T1's cable-side center taps (Mode B). On the PHY side the pairs are clamped by ESD array D1 (WHALD03G4U) and connect to the 10/100 PHY U1 (JL1101BR-NI), which connects to the video SoC over RMII. T1's cable-side center taps carry PoE power to the bridge rectifier (see the PoE powered chain) and divert surges to chassis ground through gas discharge tube G1. Refer to the PHY datasheet for center-tap termination and crystal load capacitor values.
Board bill of materials
Click any row to jump to that position and view its selection notes
| No. | Zone | Position | Ref. | VOOHU category | Recommended part | Availability |
|---|---|---|---|---|---|---|
| 01 | A Port · PoE | RJ45 port (10/100 · PoE powered) | J1 | RJ45 Connectors | SYT561188AB1A1DB4 | VOOHU |
| 02 | A Port · PoE | Gas discharge tube (cable side to chassis) | G1 | GDT | WHGD090V1P0B | VOOHU |
| 03 | A Port · PoE | PoE LAN transformer | T1 | Gigabit LAN Transformers | WHSG24701D1 | VOOHU |
| 04 | A Port · PoE | Ethernet ESD array | D1 | TVS / ESD | WHALD03G4U | VOOHU |
| 05 | A Port · PoE | 10/100 PHY (RMII) | U1 | Ethernet PHY | JL1101BR-NI | VOOHU |
| 06 | A Port · PoE | PHY 25MHz crystal | Y1 | — | — | Non-VOOHU |
| 07 | B PoE PD | PoE input bridge rectifier | D2 | — | — | Non-VOOHU |
| 08 | B PoE PD | PD input TVS | D3 | TVS / ESD | WHTB058VA | VOOHU |
| 09 | B PoE PD | PoE PD controller + flyback PWM | U2 | — | — | Non-VOOHU |
| 10 | B PoE PD | PoE flyback transformer | T2 | PoE Power Transformers | WH13P-12L2 | VOOHU |
| 11 | B PoE PD | Secondary synchronous rectifier | U3 | — | — | Non-VOOHU |
| 12 | B PoE PD | Opto feedback | U4 | — | — | Non-VOOHU |
| 13 | C Audio | External audio line terminal (Line In / Out) | J2 | — | — | Non-VOOHU |
| 14 | C Audio | Audio line ESD ×2 | D4 D5 | TVS / ESD | WHALD30E2B | VOOHU |
| 15 | C Audio | Audio isolation transformer ×2 | T3 T4 | Audio Transformer | WHTT4001 | VOOHU |
| 16 | C Audio | Speaker amplifier | U5 | — | — | Non-VOOHU |
| 17 | C Audio | Microphone / speaker connector | J3 | — | — | Non-VOOHU |
| 18 | D Access I/O | Access terminal (lock / door contact / exit button) | J4 | — | — | Non-VOOHU |
| 19 | D Access I/O | Access input ESD | D6 | TVS / ESD | WHALD30E2B | VOOHU |
| 20 | D Access I/O | Lock relay | K1 | — | — | Non-VOOHU |
| 21 | D Access I/O | Keypad FPC connector | J5 | — | — | Non-VOOHU |
| 22 | D Access I/O | Keypad line ESD array | D8 | TVS / ESD | WHTA5V01P2C | VOOHU |
| 23 | D Access I/O | Card reader connector | J6 | — | — | Non-VOOHU |
| 24 | E SoC · Video | Video SoC (ISP · encoding · audio codec) | U6 | — | — | Non-VOOHU |
| 25 | E SoC · Video | DDR memory | U7 | — | — | Non-VOOHU |
| 26 | E SoC · Video | SPI Flash | U8 | — | — | Non-VOOHU |
| 27 | E SoC · Video | Main clock crystal | Y2 | — | — | Non-VOOHU |
| 28 | E SoC · Video | Camera module connector | J7 | — | — | Non-VOOHU |
| 29 | E SoC · Video | Fill-light driver | U9 | — | — | Non-VOOHU |
| 30 | E SoC · Video | Core supply filter molded inductor ×2 | L1 L2 | Molded Inductors | WHYTA0420 Series | VOOHU |
| 31 | F Power | DC 12V auxiliary power terminal | J8 | — | — | Non-VOOHU |
| 32 | F Power | Power line CMC (auxiliary input EMI) | L3 | Power Line CMC | WHAL-7060A-102T0 | VOOHU |
| 33 | F Power | PoE / auxiliary input ORing diodes | D9 D10 | — | — | Non-VOOHU |
| 34 | F Power | Synchronous buck ×2 (core / 3.3V) | U10 U11 | — | — | Non-VOOHU |
| 35 | F Power | DC-DC molded inductor ×2 | L4 L5 | Molded Inductors | WHYTA0530 Series | VOOHU |
Resources & downloads
Board bill of materials
Reference designators, zones, VOOHU categories, recommended parts and availability for all 35 positions. Opens directly in Excel.
Datasheet collection
Datasheet PDFs for the VOOHU parts recommended on this board.
Design files & footprint library
Schematic, PCB, and VOOHU part footprints and 3D models.
Coming soonRequest the full video intercom reference design packagefull package
Includes the BOM, datasheets for the recommended VOOHU parts and position-by-position selection notes. If you need recommendations for your power scheme, PoE power class, port type or external audio line, describe it in the requirements field. We reply within 24 hours on working days.