PoE IP Speaker Reference Design
Illustrative design of an outdoor PoE IP speaker (column speaker) main board for campus, school, transport-hub and perimeter public address: Fast Ethernet access, IEEE 802.3at (PoE+) power over the same cable, isolated flyback 12 V output; the host SoC receives and decodes network audio streams and drives a mono Class-D amplifier over I²S; audio-transformer-isolated line input / output, plus a short-circuit (dry-contact) alarm input and a relay linkage output. This page gives the function, selection notes and available VOOHU part numbers for 30 component positions.
Illustrative PCB ⇄ Schematic
The illustrative layout shows placement and component positions; click any position for selection notes, recommended parts and package. The board is an illustration arranged by functional zone (not an actual layout) and shows only the speaker main board; the RJ45 port, line input / output terminals, alarm terminal and speaker terminal sit on the bottom edge, and the speaker driver is an external node.
The Fast Ethernet TX / RX pairs are identical, so only one pair is drawn. RJ45 J1 is a plain RJ45 without magnetics, coupled through the discrete gigabit PoE+ LAN transformer T1 (WHSG24706-1PTG); the PHY-side pairs are clamped by ESD array D1 (WHALD03G4U) and go to the 10/100 PHY U1 (JL1101BR-NI), which connects to the host SoC over RMII. The four cable-side center taps of T1 deliver PoE power to the rectifier bridge (Mode A or B, see the PoE PD chain), and gas discharge tube G1 diverts surges to chassis ground. Center-tap termination and crystal load capacitor values per the PHY datasheet.
Board bill of materials
Click any row to jump to that position and view its selection notes
| No. | Zone | Position | Ref. | VOOHU category | Recommended part | Availability |
|---|---|---|---|---|---|---|
| 01 | A Ethernet port | RJ45 port (PoE powered) | J1 | RJ45 Connectors | SYT561188AB1A1DB4 | VOOHU |
| 02 | A Ethernet port | Gas discharge tube (cable side to chassis) | G1 | GDT | WHGD200V1P0B | VOOHU |
| 03 | A Ethernet port | Gigabit PoE+ LAN transformer | T1 | Gigabit LAN Transformers | WHSG24706-1PTG | VOOHU |
| 04 | A Ethernet port | Ethernet ESD array | D1 | TVS / ESD | WHALD03G4U | VOOHU |
| 05 | A Ethernet port | 10/100 PHY (RMII) | U1 | Ethernet PHY | JL1101BR-NI | VOOHU |
| 06 | A Ethernet port | PHY 25MHz crystal | Y1 | — | — | Non-VOOHU |
| 07 | B PoE PD | PoE input bridge rectifier | D2 | — | — | Non-VOOHU |
| 08 | B PoE PD | PD input TVS | D3 | TVS / ESD | WHTB058VA | VOOHU |
| 09 | B PoE PD | PoE PD controller + flyback PWM | U2 | — | — | Non-VOOHU |
| 10 | B PoE PD | PoE flyback transformer | T2 | PoE Power Transformers | WH13P-12H5 | VOOHU |
| 11 | B PoE PD | Secondary synchronous rectifier | U3 | — | — | Non-VOOHU |
| 12 | B PoE PD | Opto feedback | U4 | — | — | Non-VOOHU |
| 13 | C Line audio | Line input / output terminals | J2 J3 | — | — | Non-VOOHU |
| 14 | C Line audio | Line-port ESD ×2 | D4 D5 | TVS / ESD | WHALD30E2B | VOOHU |
| 15 | C Line audio | Line input audio transformer | T3 | Audio Transformer | WHTT6016 | VOOHU |
| 16 | C Line audio | Line output audio transformer | T4 | Audio Transformer | WHTT6010 | VOOHU |
| 17 | C Line audio | Audio codec | U5 | — | — | Non-VOOHU |
| 18 | D Alarm I/O | Alarm input / linkage output terminal | J4 | — | — | Non-VOOHU |
| 19 | D Alarm I/O | Alarm input ESD | D6 | TVS / ESD | WHALD30E2B | VOOHU |
| 20 | D Alarm I/O | Opto-isolated input | U6 | — | — | Non-VOOHU |
| 21 | D Alarm I/O | Linkage output relay | K1 | — | — | Non-VOOHU |
| 22 | E Amp · speaker | Class-D amplifier (I²S input) | U7 | — | — | Non-VOOHU |
| 23 | E Amp · speaker | Amplifier output filter inductors ×2 | L1 L2 | Molded Inductors | WHYT0630 Series | VOOHU |
| 24 | E Amp · speaker | Speaker output terminal | J5 | — | — | Non-VOOHU |
| 25 | F Core · power | Host SoC (network audio processor) | U8 | — | — | Non-VOOHU |
| 26 | F Core · power | DDR memory | U9 | — | — | Non-VOOHU |
| 27 | F Core · power | SPI Flash | U10 | — | — | Non-VOOHU |
| 28 | F Core · power | MCU crystal | Y2 | — | — | Non-VOOHU |
| 29 | F Core · power | Synchronous buck ×2 (3.3 V / core) | U11 U12 | — | — | Non-VOOHU |
| 30 | F Core · power | DC-DC molded inductor ×2 | L3 L4 | Molded Inductors | WHYT0630 Series | VOOHU |
Resources & downloads
Board bill of materials
Reference designators, zones, VOOHU categories, recommended parts and availability for all 30 positions. Opens directly in Excel.
Datasheet collection
Datasheet PDFs for the VOOHU parts recommended on this board.
Design files & footprint library
Schematic, PCB, and VOOHU part footprints and 3D models.
Coming soonRequest the full IP speaker reference design packagefull package
Includes the BOM, datasheets of the recommended VOOHU parts and position-by-position selection notes. If you need selection advice for your PoE power class, amplifier power or line-interface type, please describe it in your request. We reply within 24 hours on working days.