Entrance / Exit License Plate Recognition Camera Main Board Reference Design
An illustrative main board design for the license plate recognition camera used at car park, campus and residential entrances / exits: Fast Ethernet (100BASE-TX) uploads recognition results and vehicle snapshots, the camera is powered over the same cable by IEEE 802.3af PoE or from DC 12 ~ 24V through the terminal block; the vision SoC connects to the front-end image sensor board, an isolated RS-485 port links the barrier gate / LED display, a relay dry contact raises the barrier arm, optocoupler-isolated inputs take the loop-detector trigger for snapshots, with an on-board fill-light constant-current driver, microSD offline storage and an audio line output for voice announcements. This page covers the function, selection notes and available VOOHU parts for 35 component positions.
Illustrative PCB ⇄ Schematic
The illustrative layout shows placement and BOM positions; click any position to view selection notes, recommended parts and package. The board is an illustration arranged by functional zone (not the actual layout) and shows only the recognition camera main board; the RJ45 port, I/O terminal block and fill-light board connector sit on the bottom edge, and the front-end image sensor board connects through the board-to-board connector at the top as an external node.
Fast Ethernet uses only the TX / RX pairs; one pair is drawn and the other is identical. RJ45 J1 is a plain RJ45 without magnetics, coupled through the discrete PoE LAN transformer T1 (WHSG24701D1, 5000 Vrms isolation, PoE ≤ 350 mA); the PHY-side pairs are clamped by ESD array D1 (WHALD03G4U) before the Fast Ethernet PHY U1 (JL1101BR-NI), which connects to the vision SoC over RMII. The cable-side center taps of T1 (including spare pairs 4/5 and 7/8) bring PoE power out to the bridge rectifier (see the PoE powered chain), and GDT G1 diverts surges to chassis ground. Refer to the PHY datasheet for center-tap termination and the RMII reference-clock connection.
Board bill of materials
Click any row to jump to that position and view its selection notes
| No. | Zone | Position | Ref. | VOOHU category | Recommended part | Availability |
|---|---|---|---|---|---|---|
| 01 | A Ethernet · PoE | RJ45 port (Fast Ethernet · PoE powered) | J1 | RJ45 Connectors | SYT561188AB1A1DB4 | VOOHU |
| 02 | A Ethernet · PoE | Gas discharge tube (cable side to chassis) | G1 | GDT | WHGD200V1P0B | VOOHU |
| 03 | A Ethernet · PoE | PoE LAN transformer (center taps on 4 channels) | T1 | Gigabit LAN Transformers | WHSG24701D1 | VOOHU |
| 04 | A Ethernet · PoE | Ethernet ESD array | D1 | TVS / ESD | WHALD03G4U | VOOHU |
| 05 | A Ethernet · PoE | 10/100 PHY (RMII) | U1 | Ethernet PHY | JL1101BR-NI | VOOHU |
| 06 | B PoE PD | PoE input bridge rectifier | D2 | — | — | Non-VOOHU |
| 07 | B PoE PD | PD input TVS | D3 | TVS / ESD | WHTB058VA | VOOHU |
| 08 | B PoE PD | PoE PD controller + flyback PWM | U2 | — | — | Non-VOOHU |
| 09 | B PoE PD | PoE flyback transformer | T2 | PoE Power Transformers | WH13P-12L2 | VOOHU |
| 10 | B PoE PD | Secondary rectifier diode | D4 | — | — | Non-VOOHU |
| 11 | C Barrier I/O | I/O terminal block (RS-485 / relay / loop input / audio / DC input) | J2 | — | — | Non-VOOHU |
| 12 | C Barrier I/O | RS-485 GDT ×2 | G2 G3 | GDT | WHGD090V1P0B | VOOHU |
| 13 | C Barrier I/O | RS-485 bus TVS (secondary clamp) | D5 | TVS / ESD | WHALD30E2B | VOOHU |
| 14 | C Barrier I/O | RS-485 bus common-mode choke | L1 | Signal Line CMC | WHAC-4532A-601ZP0 | VOOHU |
| 15 | C Barrier I/O | Isolated RS-485 transceiver | U3 | — | — | Non-VOOHU |
| 16 | C Barrier I/O | Push-pull isolated power transformer | T3 | Push-Pull Transformers | WHST06K14A0 | VOOHU |
| 17 | C Barrier I/O | Push-pull driver + isolated-side regulation | U4 | — | — | Non-VOOHU |
| 18 | C Barrier I/O | Loop / coil input ESD | D6 | TVS / ESD | WHALD30E2B | VOOHU |
| 19 | C Barrier I/O | Dual-channel optocoupler input | U5 | — | — | Non-VOOHU |
| 20 | C Barrier I/O | Barrier relay output (with driver transistor) | Q1 K1 | — | — | Non-VOOHU |
| 21 | C Barrier I/O | Audio line-output isolation transformer (optional) | T4 | Audio Transformer | WHTT4001 | VOOHU |
| 22 | D Core · Imaging | Image sensor board connector | J3 | — | — | Non-VOOHU |
| 23 | D Core · Imaging | Vision SoC (ISP + recognition algorithm) | U6 | — | — | Non-VOOHU |
| 24 | D Core · Imaging | DDR memory | U7 | — | — | Non-VOOHU |
| 25 | D Core · Imaging | Flash (system / firmware) | U8 | — | — | Non-VOOHU |
| 26 | D Core · Imaging | microSD socket (offline storage) | J4 | SD Card Sockets | WHTF190T123101W | VOOHU |
| 27 | D Core · Imaging | Core supply filter molded inductor ×2 | L2 L3 | Molded Inductors | WHYTA0420 Series | VOOHU |
| 28 | E Power · Fill light | DC input TVS | D7 | TVS / ESD | WHTB058VA | VOOHU |
| 29 | E Power · Fill light | Power-line common-mode choke (DC input EMI) | L4 | Power Line CMC | WHAL-7060A-102T0 | VOOHU |
| 30 | E Power · Fill light | PoE / DC input ORing diodes | D8 D9 | — | — | Non-VOOHU |
| 31 | E Power · Fill light | Synchronous buck ×3 (core / DDR / 3.3V) | U9 U10 U11 | — | — | Non-VOOHU |
| 32 | E Power · Fill light | DC-DC molded inductor ×3 | L5 L6 L7 | Molded Inductors | WHYTA0530 Series | VOOHU |
| 33 | E Power · Fill light | Fill-light LED constant-current driver | U12 | — | — | Non-VOOHU |
| 34 | E Power · Fill light | Fill-light driver power inductor | L8 | Molded Inductors | WHYT1030 Series | VOOHU |
| 35 | E Power · Fill light | Fill-light board connector | J5 | — | — | Non-VOOHU |
Resources & downloads
Board bill of materials
Reference designators, zones, VOOHU categories, recommended parts and availability for all 35 positions. Opens directly in Excel.
Datasheet collection
Datasheet PDFs for the VOOHU parts recommended on this board.
Design files & footprint library
Schematic, PCB, and VOOHU part footprints and 3D models.
Coming soonRequest the license plate recognition reference design full package
Includes the BOM, datasheets for the recommended VOOHU parts and position-by-position selection notes. If you need advice for your power option (PoE / DC), RS-485 cable length or outdoor surge-protection requirements, describe them in the request. We reply within 24 hours on working days.