The VOOHU WH290Z019D0S01 is a functional alternative to the Lian Xin XDSFP-020-0852, a 20-position SFP+ 1×1 surface-mount connector with a 0.80 mm pitch — verify with samples in your design. Read the two drawings side by side and both recommended PCB pages print twenty 2.00 × 0.50 mm pads and two Ø1.55 mm locating holes. The notes on materials, forces, ratings and reflow print alike too. What changes is the body. Lian Xin draws it 8.20 mm deep and 5.20 mm high; VOOHU draws it 7.70 mm deep and 5.28 mm high. Both bodies sit under the SFP cage, so this change is settled on the bench with your cage and your modules, not in the datasheet.
#XDSFP-020-0852 datasheet and WH290Z019D0S01 datasheet, line by line
Lian Xin Technology publishes the XDSFP-020-0852 as a three-sheet customer drawing, revision A, first issued on 2021-08-01. VOOHU's datasheet for the WH290Z019D0S01 is revision A0. On both, sheet 1 holds the outline and a numbered list of notes, and sheet 2 the recommended PCB layout. The table copies values as printed, in millimetres unless a unit is given; page and note numbers follow each value.
A few smaller side-view and front-view dimensions also differ between the two outlines. Neither drawing labels what those dimensions describe, so they are left out of the table; lay the two sheet 1 outlines over each other if your inspection program depends on them.

#SFP connector PCB: the land pattern is not where this change lives
For the Layout engineer the comparison is short. Both recommended PCB sheets print the values in the table above, from pad size and pitch to the two locating holes and the other unlabelled dimensions. Still overlay the VOOHU sheet 2 on your existing footprint before you sign off, because no FAE has yet confirmed in writing that the layouts are interchangeable. One reading trap: the 8.20 mm printed on sheet 2 is a PCB layout dimension, while the 8.20 mm on the Lian Xin sheet 1 is the body depth. They are different dimensions that happen to share a number, and mixing them up is the quickest way to misread this comparison.
#SFP cage and connector: where 8.20 vs. 7.70 mm and 5.20 vs. 5.28 mm show up
On a working board this connector is never seen on its own. The cage is mounted over it, and a module slides down the cage until its edge card enters the connector slot and the latch catches. Both drawings measure body depth on the side view, from the front end with the lead-in chamfer to the rear end, so the two figures can be compared directly. The VOOHU body is 0.50 mm shorter and 0.08 mm taller, both by subtraction from the printed values.
Neither drawing shows a cage, so neither can tell you what those two numbers do to your assembly. That is why this article gives no clearance figure. What the mechanical engineer can do is check the three places where body size meets the cage and the module: whether the module reaches full engagement in the connector at the moment its latch catches, whether the inside of the cage roof clears a body that is 5.28 mm high, and whether anything behind the connector, inside the cage or under its rear wall, was placed against the 8.20 mm outline. If your cage drawing gives its own position for the connector, measure the VOOHU sample against that position, not against the Lian Xin outline.
#On the SMT line: what the EMS partner changes for the WH290Z019D0S01
Less than you might expect, but not nothing. Both parts come on tape and reel, and both drawings give a reflow window of 255–265 °C for 5–10 s, so the profile already qualified for the Lian Xin part is the place to start. The part library is where the edits go. The placement program needs the new body height of 5.28 mm, and the vision or AOI outline should be taught from a VOOHU sample rather than copied from the old part, because the body is shorter and several minor outline dimensions differ. Coplanarity is 0.10 mm on both drawings, so inspect joints to the criteria you already use; what deserves a closer look on the first boards is whether the shorter body changes how the vision system finds the part.
#Fit check list for an XDSFP-020-0852 to WH290Z019D0S01 change
#When the swap is quick, and when to plan more time
The quickest case is a board where the cage and the module list are both still open: run checks 1 to 3 once with the cage you intend to release and the WH290Z019D0S01 goes into the BOM alongside the Lian Xin part. If the product is already shipping with a released cage, a qualified module list and an EMS line tuned to the XDSFP-020-0852, the order matters. The mechanical checks come first because they need real hardware and can stop the change; the library edits follow; the purchasing record closes it. If one module on your list behaves differently in check 1 or 2, keep the Lian Xin part on that SKU until the cause is understood, rather than approving the alternate across the board.
#FAQ
What is an equivalent for the Lian Xin XDSFP-020-0852 SFP+ connector?
The VOOHU WH290Z019D0S01 is a functional alternative — verify with samples in your design. It is a 20-position SFP+ 1×1 SMT connector with a 0.80 mm pitch and an 11.00 mm wide body, and its recommended PCB sheet prints the values found on the Lian Xin drawing. No FAE has confirmed interchangeability in writing, so treat it as an alternate that needs a fit check.
What are the SFP connector dimensions that differ between the two parts?
Body depth on the side view is 8.20 mm on the Lian Xin drawing and 7.70 mm on the VOOHU datasheet; body height is 5.20 mm and 5.28 mm. Both drawings print width 11.00 mm, pitch 0.80 mm, terminal width 0.20 ± 0.05 mm, Ø1.40 mm locating posts and 0.10 mm coplanarity. The body sits inside the SFP cage, so check module seating, latching and roof clearance with your own cage rather than relying on a calculated gap.
Is the 40 N insertion force for mounting the connector in the cage?
No. On both drawings the 40 N maximum insertion and 11.5 N maximum extraction force describe a module edge card going into and out of the connector. The connector itself is soldered to the board. Neither drawing gives a force for fitting the cage.
Can the existing reflow profile be used for the WH290Z019D0S01?
Both drawings give a reflow condition of 255–265 °C for 5–10 s, so your qualified profile is a reasonable starting point. Update the component height to 5.28 mm in the placement program, teach the outline from a sample, and inspect the first boards to your usual standard. Neither drawing specifies a stencil.
#Getting WH290Z019D0S01 samples for a cage fit check
When you request WH290Z019D0S01 samples, give the part number of the cage on your board and the modules you need to qualify, and say whether the board was laid out from the Lian Xin drawing. Samples are available for evaluation, and selected parts are free of charge. Our FAE team will be glad to confirm the options for your project. Our FAE team can suggest suitable parts and help check the design — for this change, that means looking at your cage drawing and footprint against the WH290Z019D0S01 datasheet before the samples go on a board.
VOOHU supplies RJ45 and SFP connectors, LAN and PoE transformers and common mode chokes from Suzhou, China, to more than 1,500 customers.
If the cage is being second-sourced too, VOOHU's SFP cages and connectors are listed together, so the cage and the board connector can be chosen as a pair and checked in one build.
Related product: WH290Z019D0S01 — SFP+ 1×1 connector, 20 positions, 0.80 mm pitch, SMT, 11.00 mm wide body. Another comparison for this part: Amphenol UE76-A20-2000T alternative.
#Sources
- Lian Xin Technology, customer drawing XDSFP-020-0852, SFP+ 1X1 connector, Rev A (first issue 2021-08-01), sheets 1–2.
- VOOHU, WH290Z019D0S01 datasheet, Rev A0, pages 1–2.
Need a quote, samples or selection support?
Part number WH290Z019D0S01 is filled in for you. Add the quantity and lead time and submit. Our FAE team will be glad to confirm the options for your project.
Before you order: samples, MOQ, lead time and import duties in our ordering guide →


