RJ45 jack dimensions are not one standard size. The plug opening follows a common interface, so a standard plug fits any of them, but the body around it changes with the construction. On VOOHU drawings, a plain single-port tab-down jack, the SYT57221188IWA1DB3, is 15.20 mm wide, 18.10 mm deep and 12.70 mm high. A 10/100 MagJack, which is an RJ45 jack with integrated magnetics, the SYT111B002BA2A1D, measures 16.00 × 21.10 × 13.45 mm. The 99TGWHQ618G830415 gigabit MagJack stands 11.05 mm high, the SYT561288AB2A3DY1027 1×2 jack is 32.20 mm wide, and the SYT21Q042DB3A4D068 2×1 stacked MagJack is 25.50 mm high. Width, depth and height are only the start: also check pin length below the board and the panel opening on the drawing of the exact part.

#What are the dimensions of an RJ45 connector in millimeters?
The table lists the outline of six VOOHU RJ45 jacks, one per construction. Width is across the plug opening, depth is from the front face to the rear of the body, and height is from the board surface to the top of the jack.
Values are as marked on each VOOHU outline drawing. Where no tolerance is shown, the drawing's general tolerance applies, for example ±0.25 mm on two-decimal dimensions.
#Are all RJ45 jacks the same size?
At the plug opening, yes; around it, no. IEC 60603-7 specifies the common interface dimensions for this family of 8-way modular connectors so that they intermate, which is why one patch cord fits every port on a switch. Everything behind the opening is up to the jack design. Integrated magnetics add depth, a tab-up or tab-down latch moves the opening within the body, LEDs, shields and EMI fingers add width, and stacked or ganged ports multiply the outline. That is why the heights in the table run from 11.05 mm to 25.50 mm for parts that all take the same plug.
Width, depth, height above the board and pin length on a single-port MagJack, with the reference panel cutout, using the SYT111B002BA2A1D drawing as the example. Illustrative, not to scale; check the drawing of the exact part.
#RJ45 connector length: how much deeper is a MagJack?
Depth is the figure that changes most when you move from a plain jack to a MagJack, because the magnetics sit inside the body behind the contacts. Compare two single-port tab-down parts: the plain SYT57221188IWA1DB3 is 18.10 mm deep, while the SYT111B002BA2A1D MagJack is 21.10 mm deep. The gigabit 99TGWHQ618G830415 is 23.88 mm deep, and the 2×1 SYT21Q042DB3A4D068 is 28.50 mm.
Depth decides where the next component can start behind the board edge, so reserve it in the placement plan before routing the PHY. With a discrete LAN transformer and a plain jack, the magnetics move onto the board instead, so compare the jack depth plus the transformer area rather than the jack alone.
The footprint itself, meaning pad sizes, hole positions and pin numbering, is a separate step; see our RJ45 jack pinout with integrated magnetics for that.
#RJ45 jack height above the board, and pin length below it
Height above the board sets the minimum gap to the lid or to a board above. Among the jacks in the table, the 99TGWHQ618G830415 is the lowest at 11.05 mm, and the stacked 2×1 is the tallest at 25.50 mm because it puts two ports in one column. A 180° jack such as the SYT52241188IWA1DB4 takes the plug from above, so its 16.20 mm height adds to the plug and cable bend in your height budget, and its drawing also marks a 0.40 mm gap between body and board. For thin enclosures, browse our low-height RJ45 jacks; sink-mount jacks, which sit partly in a board cutout, are compared in RJ45 mechanical structure selection.
Pin length matters on the other side. It ranges from 1.80 mm on the 99TGWHQ618G830415 to 3.6 mm on the SYT111B002BA2A1D. Compare it with your board thickness: it decides how far the pins stand out on the solder side, which matters for wave soldering and for anything mounted under the board.
#What size hole for an RJ45 plug? Panel openings for PCB jacks
When the jack faces a panel, the opening has to clear the plug opening, the LEDs and any EMI fingers, and absorb the position tolerance between board and panel. Take it from the jack drawing rather than from the body width. The SYT111B002BA2A1D drawing gives a reference panel cutout of 16.30 × 13.75 mm (±0.10), marked reference only, so confirm it on your own stack-up. The 99TGWHQ618G830415 drawing shows a panel opening of 18.34 × 11.68 mm (±0.25 each); its EMI fingers, 20.83 mm across, are there to contact the panel around that opening.
If the port is a coupler, a waterproof receptacle or a locking housing instead, the cutout comes from that part; see the panel mount RJ45 connector guide.
#Multi-port RJ45 jack dimensions: 1×2, 2×1 and 2×N
Ganged jacks trade width for height. The SYT561288AB2A3DY1027 puts two ports side by side in a body 32.20 mm wide, 16.00 mm deep and 13.20 mm high. The SYT21Q042DB3A4D068 stacks two MagJack ports in a body only 17.21 mm wide but 25.50 mm high and 28.50 mm deep. Pick the 1×2 when the panel is wide and the enclosure is thin, and the 2×1 when the board edge is short and there is height to spare. For 2×4 and 2×8 banks, the outline depends on the series, so compare drawings in the multi-port RJ45 selector.
#Which VOOHU RJ45 jack fits your enclosure?
- No magnetics needed on the jack: the SYT57221188IWA1DB3 is the compact plain reference, 18.10 mm deep.
- 10/100 port with integrated magnetics: the SYT111B002BA2A1D, with a reference panel cutout on its drawing.
- Gigabit in a thin enclosure: the 99TGWHQ618G830415, 11.05 mm high with 1.80 mm pins.
- Two ports: the SYT561288AB2A3DY1027 side by side, or the SYT21Q042DB3A4D068 stacked.
To narrow by speed, LEDs or tab direction, use the MagJack selector; offset and other structures are in offset RJ45 connectors.

#FAQ
Are all RJ45 connectors the same size?
No. The plug opening is common, so any standard RJ45 plug mates with any compliant jack, but jack bodies differ. On VOOHU drawings, single-port right-angle jacks range from 11.05 mm high (99TGWHQ618G830415) to 13.45 mm (SYT111B002BA2A1D), and a 180° jack stands 16.20 mm. Size the enclosure from the drawing of the part you will buy.
Where do I get the PCB footprint for an RJ45 jack?
From the recommended PCB layout on the jack drawing, not from the outline. For example, the SYT52241188IWA1DB4 layout uses eight Ø0.90 mm contact holes and two Ø3.20 mm locating-post holes 11.43 mm apart. For MagJack pin numbering and footprint checks, see our RJ45 jack pinout with integrated magnetics.
What are the dimensions of an RJ45 MagJack?
It depends on speed and port count. On VOOHU drawings, the SYT111B002BA2A1D 10/100 MagJack is 16.00 mm wide, 21.10 mm deep and 13.45 mm high; the 99TGWHQ618G830415 gigabit MagJack is 17.53 mm wide (20.83 mm over its EMI fingers), 23.88 mm deep and 11.05 mm high; and the SYT21Q042DB3A4D068 2×1 MagJack is 17.21 × 28.50 × 25.50 mm.
Get RJ45 jack samples sized for your enclosure
Send the height and depth you have, the panel opening, the board thickness, the port count and the speed through our sample request form. Our FAE team can suggest VOOHU RJ45 jacks that fit and send the drawings, so you can check the outline and panel cutout before layout. Samples are available for evaluation, and selected parts are free of charge. Our FAE team will be glad to confirm the options for your project. VOOHU supplies RJ45 and SFP connectors, LAN and PoE transformers and common mode chokes from Suzhou, China, to more than 1,500 customers.
Need a quote, samples or selection support?
Part number SYT57221188IWA1DB3 is filled in for you. Add the quantity and lead time and submit. Our FAE team will be glad to confirm the options for your project.
Before you order: samples, MOQ, lead time and import duties in our ordering guide →


