Skip to main content

Würth Elektronik 7499010211A Alternative: VOOHU SYT111B002FA2A1D Comparison

·Published ·9 min read
Alternative part See report
Your part · Würth Elektronik 7499010211A
VOOHU alternative SYT111B002FA2A1D10/100M 1*1 90° non-PoE G/Y RJ45 Connector
ParameterWürth 7499010211A (spec. for release Rev 03)VOOHU SYT111B002FA2A1D (DS rev A0)
Turns ratio1:1 ±3%, TX and RX (p1)1CT:1CT ±2% (p2)
OCL350 µH min at 100 kHz, 100 mV, 8 mA DC bias (p1)350 µH min at 100 kHz, 100 mV, 8 mA DC (p2)
Hi-pot2250 V DC, 1 min (p1)1500 V AC and 2250 V DC, 6 s, 1 mA, primary to secondary (…
Insertion loss−1.4 dB max, 1–100 MHz (p1)−1.0 dB max, 1–100 MHz (p2)

Compiled from both manufacturers' published datasheets. Verify with samples and the PCB footprint before production.

If the Würth Elektronik 7499010211A on your BOM needs a second source, the VOOHU SYT111B002FA2A1D is a functional alternative — verify with samples in your design. Both are single-port, tab-down, through-hole RJ45 jacks with integrated magnetics (MagJacks) for 10/100BASE-TX ports. The published schematics put the same signals on pins 1–6, leave pin 7 unconnected and tie the four 75 Ω resistors to pin 8 through 1000 pF / 2 kV. The green LED is on the left and the yellow on the right, with the same polarity, and both sheets specify 350 µH minimum OCL at 8 mA. Much of the change is paperwork: the two datasheets state the isolation test under different conditions, so your hi-pot step and safety file have to quote the VOOHU conditions, and the VOOHU part operates from −40 to +85 °C, the Würth part from 0 to +70 °C.

SYT111B002FA2A1D
I/O Connector · Network Connector (RJ45/RJ11)SYT111B002FA2A1D10/100M 1*1 90° non-PoE G/Y RJ45 Connector
RJ45 Connector90°1 x 1Down10/100Mnon-PoE

#What the 7499010211A datasheet (Rev 03) lists, next to the SYT111B002FA2A1D

Würth publishes this part as a three-page "Spezifikation für Freigabe / specification for release", revision 03 of 20 November 2017, with German and English labels side by side. Nearly everything a buyer or a quality engineer needs sits on page 1: the outline, the recommended hole pattern (labelled "B Lötpad", solder pad), the electrical values, the materials and the hi-pot and temperature lines. Page 2 is the schematic and page 3 the packaging. The VOOHU datasheet, revision A0, also has three pages: outline, hole pattern, materials and mechanical data on page 1, then schematic, electrical table and LED data on page 2. Both hole patterns are drawn from the component side, but the Würth drawing is turned 180° relative to the VOOHU one; rotate it and pin 1, the LED pins 9–12, the shield pins and the locating posts correspond. Dimensions below are in millimetres, and "not stated" means the datasheet gives no value.

ParameterWürth 7499010211A (spec. for release Rev 03)VOOHU SYT111B002FA2A1D (DS rev A0)
Type1 port, tab down, through-hole; 10/100Base-TX, IEEE 802.3u (p1)1×1, tab down (p1 title block); DIP, 10/100BASE-TX (product page)
Pin namesTD+ 1, TD− 2, RD+ 3, TCT 4, RCT 5, RD− 6; pin 7 not connected; 4 × 75 Ω to pin 8 through 1000 pF / 2 kV (p2)TD+ 1, TD− 2, RD+ 3, CT 4, CT 5, RD− 6; pin 7 not connected; 4 × 75 Ω to GND pin 8 through 1000 pF / 2 kV (p2)
Turns ratio1:1 ±3%, TX and RX (p1)1CT:1CT ±2% (p2)
OCL350 µH min at 100 kHz, 100 mV, 8 mA DC bias (p1)350 µH min at 100 kHz, 100 mV, 8 mA DC (p2)
Insertion loss−1.4 dB max, 1–100 MHz (p1)−1.0 dB max, 1–100 MHz (p2)
Return loss−16 / −13.5 / −12 / −10 dB at 1–30 / 30–45 / 45–60 / 60–80 MHz, 100 Ω (p1)−18 / −14 / −10 dB at 1–30 / 30–60 / 60–100 MHz (p2)
Common-mode rejection−30 dB min, 1–100 MHz (p1)−30 dB min, 1–100 MHz (p2)
Crosstalk−30 dB min, 1–100 MHz (p1)−40 / −35 / −30 dB at 1–30 / 30–60 / 60–100 MHz (p2)
Hi-pot2250 V DC, 1 min (p1)1500 V AC and 2250 V DC, 6 s, 1 mA, primary to secondary (p2)
LEDsGreen left, pin 9 + / 10; yellow right, pin 12 + / 11; 1.8–2.8 V at 20 mA (p1, p2)Green left, pin 9 → 10, 568 nm, 1.85–2.45 V; yellow right, pin 12 → 11, 585 nm, 1.7–2.2 V; at 20 mA (p2)
Contact plating30 µin gold on contact area (p1)6 µin gold on contact area (p1)
Shield50 µin nickel over 0.01 in copper alloy (p1)C2680, 0.20 mm, nickel plated (p1)
Mating cycles / mating forceNot stated750 cycles min; 23 N max (p1)
Outline W × H × L15.88 × 13.50 × 21.84 max (p1)16.00 × 13.45 × 21.10 (p1)
Lead length (side view)3.05 ±0.50 (p1)3.60 / 3.20 / 3.65 (p1)
Signal-pin holesØ0.90 ×8, 1.27 / 2.54 staggered, 8.89 from post centreline (p1)Ø0.89 ×8, 1.27 / 2.54 staggered, 8.89 from post centreline (p1)
Locating-post holesØ3.25 ×2, 11.43 apart (p1)Ø3.20 ×2, 11.43 apart (p1)
Shield-pin holesØ1.60 ×2, 15.75 apart, 3.05 from post centreline (p1)Ø1.63 ×2, 15.75 apart, 3.05 from post centreline (p1)
LED holesØ1.02 ×4, 12.65 outer; rows 3.38 and 4.90 from post centreline (p1)Ø1.02 ×4, 12.64 outer; rows 3.43 and 4.95 from post centreline (p1)
Operating temperature0 to +70 °C (p1)−40 to +85 °C (p1)
Storage temperatureNot stated−40 to +85 °C (p1)
PoE ratingNot statedNot PoE rated (product page)

#Hipot test duration and voltage: rewriting the isolation step

This is the line that turns a part change into a document change. Page 1 of the Würth sheet gives a hi-pot test of 2250 V DC for 1 minute. Page 2 of the VOOHU sheet gives 1500 V AC and 2250 V DC for 6 seconds, with a 1 mA limit, primary to secondary. Each figure is the condition one manufacturer states for its own part. Neither sheet says how the other part behaves under its conditions, so the Würth line should not be carried across unchanged. It can be quoted in up to three places: the incoming inspection instruction, if jacks are hi-pot tested on receipt; the component entry in the safety or certification file; and any customer-approved drawing or parts list that names the jack. In each of them, replace the voltage, the dwell time and, where your procedure uses one, the leakage limit with the VOOHU values. If one of those documents requires a 60-second dwell for this component, do not adjust the figure to fit. Put the requirement in your sample request and ask our FAE team to confirm in writing which test conditions apply to the parts you will receive.

The jack-level test is not the same thing as the test on your finished product, which is set by your end-product standard. Our article on why Ethernet ports fail hi-pot testing covers that side.

#RJ45 gold plating, 30 µin and 6 µin: find out which document sets the number

Würth lists 30 µin of gold on the contact area, about 0.76 µm. VOOHU lists 6 µin, about 0.15 µm, and also rates the jack for at least 750 mating cycles with a mating force of 23 N maximum; the Würth sheet gives no mating-cycle figure. Before anyone debates the numbers, look up where your plating requirement actually lives, because the answer decides who has to sign off. There are three usual cases. If no document mentions contact plating, the inspection sheet simply takes the VOOHU value as its acceptance figure. If the specification says "per manufacturer's datasheet", the reference changes to the VOOHU datasheet and revision. If a product specification, customer drawing or approved-vendor note sets a thickness in its own words, that clause belongs to someone, usually the customer or your design authority, and the change needs their approval before release. Send that clause with the sample request, so the FAE team can confirm the options against it.

#Industrial temperature range on a part that replaces a 0 to +70 °C jack

For this pair, a good part of second source qualification happens in your records, and the temperature line shows how. The 7499010211A is rated 0 to +70 °C; the SYT111B002FA2A1D is rated −40 to +85 °C for both operation and storage. If your product is specified inside 0 to +70 °C, both ratings cover that range. Whether swapping a component means any update to your product certification depends on your certification scheme and the body that issued it; neither datasheet can answer that, so check it with them. The component record changes in any case: enter the VOOHU range in the BOM or component database from the VOOHU datasheet, not from the Würth one, so the two approved parts each carry their own data. On the approved-vendor list, record both part numbers with their datasheet revisions (Würth Rev 03, VOOHU rev A0) and mark the VOOHU part as a functional alternative pending sample approval. The rating becomes a design question only if the product itself is later specified below 0 °C. At that point the jack is one line in a wider review of the whole board.

#LED resistor value: one forward-voltage window on the Würth sheet, two on the VOOHU sheet

On paper the two schematics line up: the signals on pins 1–6, the unconnected pin 7, the termination and the LED positions and polarity all agree. The LED data is where the hardware designer should spend ten minutes. Würth gives one forward-voltage range for both colours, 1.8–2.8 V at 20 mA. VOOHU gives one per colour at 20 mA: 1.85–2.45 V for green and 1.7–2.2 V for yellow. Suppose, as an example, each LED is driven from a 3.3 V rail through 100 Ω, the drop across the PHY's LED pin is ignored and the 20 mA forward-voltage ranges are treated as fixed. With the Würth range the current could fall anywhere from 5.0 to 15.0 mA. With the VOOHU ranges it falls between 8.5 and 14.5 mA for green and between 11.0 and 16.0 mA for yellow. With the same resistor, the yellow LED's current range now sits higher than the green's. That matters if the two indicators are meant to look equally bright, or if the PHY pin has a sink-current limit close to your operating point. Rerun the calculation with your real rail, resistor and PHY drive figures, and size the two resistors separately if needed.

#Holes and outline: what to dry-fit on a board drawn to the Würth pattern

For the layout engineer the comparison is short. Hole positions for the signal pins, posts and shield pins match once the Würth drawing is rotated, but the recommended diameters differ slightly: signal pins Ø0.90 against Ø0.89 mm, locating posts Ø3.25 against Ø3.20 mm, shield pins Ø1.60 against Ø1.63 mm. The two LED rows sit 3.38 and 4.90 mm from the post centreline on the Würth drawing and 3.43 and 4.95 mm on the VOOHU drawing, the same 1.52 mm apart on both. The body is 16.00 mm wide and 13.45 mm high on the VOOHU sheet, against 15.88 and 13.50 mm for Würth, so check the clearance to neighbouring parts where the layout is tight. Lead lengths are drawn differently, so confirm protrusion against your board thickness. None of this replaces a dry fit: insert a sample into a bare board from your current lot and check the LED leads, shield pins and posts. A written FAE answer on the hole pattern is useful, but it does not replace that check.

#Incoming inspection checklist for adding the SYT111B002FA2A1D

Each line lists what to check, who usually owns it and what evidence to keep in the qualification file.

#CheckOwnerEvidence to file
01Hi-pot step rewritten as 1500 V AC and 2250 V DC, 6 s, 1 mA, primary to secondaryQualityRevised inspection instruction
02Safety or certification file entry for the jack updated to the VOOHU conditions; any 60 s requirement sent to the FAE teamQuality / complianceUpdated entry; written FAE reply if a 60 s dwell is required
03Contact-plating clause located: none, "per datasheet", or a stated thicknessQualityClause reference; approval from the clause owner if a thickness is stated
04Electrical acceptance limits copied band by band from the VOOHU datasheetQualityRevised inspection sheet
05BOM entry carries −40 to +85 °C from the VOOHU datasheetHardware / component engineeringComponent database record
06Approved-vendor list shows both parts, both datasheet revisions and "functional alternative, pending sample approval"PurchasingAVL entry
07LED current recalculated with the per-colour VOOHU forward voltagesHardwareCalculation note
08Dry fit in a bare board: LED leads, shield pins, posts, lead protrusion, clearance to neighboursLayout / productionFit report with board lot

#Where the SYT111B002FA2A1D fits

Single 10/100BASE-TX copper ports that carry data only, on boards where the 7499010211A is already designed in: controller and I/O boards, panel and HMI electronics, meters, small gateways and communication modules. The VOOHU product page lists the jack as not PoE rated, so ports that deliver power over the cable are outside its scope. If the same board family also uses a Pulse J0011D21BNL, our J0011D21BNL comparison covers that part against the same VOOHU jack.

Industry solutionIndustrialPLC · ServoView solution →

#FAQ

What is an equivalent for Würth 7499010211A?

VOOHU's SYT111B002FA2A1D is a functional alternative to the Würth Elektronik 7499010211A — verify with samples in your design. Both are 1×1 tab-down 10/100BASE-TX RJ45 jacks with integrated magnetics, with the same signals on pins 1–6 of the published schematics and green-left, yellow-right LEDs. Before release, rewrite the hi-pot and plating lines of your inspection documents from the VOOHU datasheet and dry-fit a sample in your board.

What hipot test duration do the 7499010211A and SYT111B002FA2A1D datasheets give?

The Würth 7499010211A datasheet (Rev 03) lists 2250 V DC for 1 minute. The VOOHU SYT111B002FA2A1D datasheet lists 1500 V AC and 2250 V DC for 6 seconds with a 1 mA limit, primary to secondary. Write your incoming test and safety file with the conditions of the part you actually fit, and send any 60-second requirement to the FAE team for written confirmation.

Is there a 7499010211A alternative rated to −40 °C?

The VOOHU SYT111B002FA2A1D is rated −40 to +85 °C for operation and storage; the 7499010211A is rated 0 to +70 °C. For a product specified within 0 to +70 °C, both ratings cover the range; update the component record, and ask your certification body whether the part change affects your product certification. If the product itself must work below 0 °C, the jack is one item in that wider design review, and samples should be tested in your design.

Do I need a different LED resistor value with the SYT111B002FA2A1D?

Possibly. Würth gives one forward-voltage range for both LEDs (1.8–2.8 V at 20 mA), while VOOHU gives 1.85–2.45 V for green and 1.7–2.2 V for yellow. With the same resistor, the yellow LED's current range sits higher than the green's. Recalculate both currents with your supply rail and PHY drive data.

#Getting SYT111B002FA2A1D samples into your qualification run

Request SYT111B002FA2A1D samples through the sample request form. It helps to attach three things from your current 7499010211A file: the incoming inspection instruction, the safety-file entry for the jack and any specification clause on contact plating. Samples are available for evaluation, and selected parts are free of charge. Our FAE team will be glad to confirm the options for your project. Our FAE team can suggest suitable parts and help check the design — for this change, going through your hi-pot and plating lines against the VOOHU datasheet, checking your LED resistor values and reviewing the hole pattern on your board.

VOOHU supplies RJ45 and SFP connectors, LAN and PoE transformers and common mode chokes from Suzhou, China, to more than 1,500 customers.

To look at other tab-down jacks with built-in magnetics, open the RJ45 connector selector with both filters already set.

Related product: SYT111B002FA2A1D — 1×1 tab-down RJ45 jack with integrated magnetics, 10/100BASE-TX, green / yellow LEDs, −40 to +85 °C.

SAMPLES & SUPPORT

Need a quote, samples or selection support?

Part number SYT111B002FA2A1D is filled in for you. Add the quantity and lead time and submit. Our FAE team will be glad to confirm the options for your project.

Before you order: samples, MOQ, lead time and import duties in our ordering guide →

REQUEST TYPE

Choose a Request Type and Fill in the Fields

Part number decided; you need samples, pricing, or lead time

Contact Details

Have attachments? Send datasheets, BOMs, or drawings to voohu@voohuele.com with your name and company, and our engineers will handle them together with this request.
  1. You see a confirmation right after submitting, and the request goes to our engineering queue

  2. Pricing and lead time within 1 business day; items without stock data are marked "To be confirmed"

  3. If information is missing, we list what we need first instead of closing the request

Geoffery BobFAE Engineer, VOOHU ElectronicArticles: Product Alternatives
RELATED

Related articles

Latest from this section.

SUBSCRIBE

Subscribe to VOOHU technical articles

Get new articles in your inbox. Unsubscribe at any time.

By subscribing you agree to our Privacy Policy